Code No.U0141 ETACS CAN timeout
caution |
- If diagnosis code U0141 is set in the transfer-ECU, always diagnose the CAN main bus line.
- Whenever the ECU is replaced, ensure that the communication circuit is normal.
|
DIAGNOSIS CODE SET CONDITIONS
Current trouble
- Connector(s) or wiring harness in the CAN bus lines between the ETACS-ECU and the transfer-ECU, the power supply system to the ETACS-ECU, the ETACS-ECU itself, or the transfer-ECU may be defective.
Past trouble
- Carry out diagnosis with particular emphasis on connector(s) or wiring harness in the CAN bus lines between the ETACS-ECU and the transfer-ECU, and the power supply system to the ETACS-ECU. For diagnosis procedures, refer to "How to cope with past trouble" (Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points
).
note |
For a past trouble, you may not find it by the M.U.T.-III CAN bus diagnostics even if there is any failure in CAN bus lines. In this case, refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points . and check the CAN bus lines. You can narrow down the possible cause of the trouble by referring to the diagnosis code, which is set regarding the CAN communication-linked ECUs (Refer to GROUP 54C - CAN Bus Line Diagnostic Flow ).
|
PROBABLE CAUSES
- Damaged wiring harness or connector
- Malfunction of the transfer-ECU
- Malfunction of the ETACS-ECU
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
Using M.U.T.-III, perform CAN bus line diagnosis.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ). and then go to Step 4.
|
|
|
|
STEP 2. M.U.T.-III other system diagnosis codes
|
|
Check whether the ETACS-ECU diagnosis codes are set or not.
|
|
Q.
Is the diagnosis code set?
|
|
YES : Diagnose the ETACS-ECU (Refer to GROUP 54A - Troubleshooting ).
|
|
|
|
Go to Step 3.
|
|
|
|
STEP 3. Check the M.U.T.-III Diagnosis code for other systems
|
|
Is diagnosis code No. U0141 set in the other ECU, which communicates with the ETACS-ECU via CAN?
|
|
Q.
Is the diagnosis code set?
|
|
Go to Step 4.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 4. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set in the transfer-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check whether the diagnosis code is set again.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the ETACS-ECU (Refer to GROUP 54A - ETACS-ECU ). After replacing the ECU, carry out the CAN bus diagnostics. Then go to Step 6.
|
|
|
|
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the ETACS-ECU and the transfer-ECU (Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 5. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set in the transfer-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check that the diagnosis code is not set again.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the transfer-ECU (Refer to ). After replacing the ECU, carry out the CAN bus diagnostics. Then go to Step 6.
|
|
|
|
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the ETACS-ECU and the transfer-ECU (Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 6. Check whether the diagnosis code is set again.
|
|
Recheck if the diagnosis code is set in the transfer-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check whether the diagnosis code is set again.
|
|
Q.
Is the diagnosis code set?
|
|
Return to Step 1.
|
|
|
|
The procedure is complete.
|
|
|