Code No. C1910:
Transmitter battery voltage, Tyre1
Code No. C1911: Tyre ID reception fail, Tyre1
Code
No. C1920: Transmitter battery voltage, Tyre2
Code No. C1921: Tyre ID reception fail,
Tyre2
Code No. C1930: Transmitter battery voltage, Tyre3
Code No. C1931: Tyre
ID reception fail, Tyre3
Code No. C1940: Transmitter battery voltage, Tyre4
Code
No. C1941: Tyre ID reception fail, Tyre4
Code No. C1950: Transmitter battery voltage,
Tyre5
Code No. C1951: Tyre ID reception fail, Tyre5
caution |
If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
|
DIAGNOSTIC FUNCTION
Code Nos. C1910, C1920, C1930, C1940, C1950
- When the reception abnormality warning is activated because of the low battery voltage
of the TPMS transmitter.
Code Nos. C1911, C1921, C1931, C1941, C1951
- When KOS&OSS-ECU cannot receive the signals from the TPMS transmitters
while driving for approximately 10 minutes, these codes are set.
TROUBLESHOOTING HINTS
The most likely causes for this diagnosis code to be set are:
- Low battery that is incorporated into the TPMS transmitter
- Damaged wiring harness and connector
- Registered IDs unmatched
- Effective ID set unmatched
- Malfunction of TPMS transmitter
- Malfunction of KOS&OSS-ECU
- The CAN bus may be defective.
|
STEP 1. M.U.T.-III CAN bus diagnosis.
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines.
|
|
Recheck if diagnosis code Nos. C1910, C1911, C1920, C1921, C1930, C1931, C1940, C1941,
C1950 or C1951 are set.
|
|
(1)Turn the ignition switch from the "LOCK" (OFF) to "ON" position.
|
|
(2)Check if the diagnosis code is set.
|
|
(3)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
Q.
Is the diagnosis code set?
|
|
Go to Step 3.
|
|
|
|
The procedure is complete.
|
|
|
|
STEP 3. Check the tyre IDs for the TPMS transmitters.
|
|
Could all the tyre IDs for the TPMS transmitters be confirmed?
|
|
Q.
Is the check result normal?
|
|
Adjust the tyre inflation pressure to the recommended value. Then road test for
a while to complete the reset function. Then go to Step 5.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Check for TPMS transmitter.
|
|
Identify the TPMS transmitter which the diagnosis code is set by TPMS transmitter check
(Refer to ).
|
|
note |
The TPMS transmitter which cannot be checked may be faulty or the ID code may not be registered,
thus do not replace it, but register the ID code. If the transmitter is faulty, it is replaced
in the ID code registration process.
|
|
|
Q.
Are there any TPMS transmitters which are identified?
|
|
Among the checked TPMS transmitters, replace the TPMS transmitters in which the
diagnosis code is set. Then register the ID codes (Refer to ).
Then go to Step 5.
|
|
|
|
Even when no transmitter is checked, register the ID codes (Refer to ).
Then go to Step 5.
|
|
|
|
STEP 5. Check whether the diagnosis code is set again.
|
|
Recheck if the diagnosis code is set.
|
|
(1)Turn the ignition switch from the "LOCK" (OFF) to "ON" position.
|
|
(2)Check if the diagnosis code is set.
|
|
(3)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
Q.
Are diagnosis code Nos. C1910, C1911, C1920, C1921, C1930, C1931, C1940, C1941, C1950
or C1951 set?
|
|
Replace the KOS&OSS-ECU (Refer to GROUP 42B - KOS&OSS-ECU),
and register the ID codes (Refer to ). Then start over at Step
1.
|
|
|
|
The procedure is complete.
|
|
|