Code No. C1266:
Motor stuck
Code No. C1273: Motor drive circuit stuck off
Code No. C1274:
Motor drive circuit stuck on
caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table
).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
|
OPERATION
- The ABS-ECU contains the power supply circuit (+BM terminal) for
the pump motor. The pump motor is energised by the motor relay, which is incorporated in the
ABS-ECU.
- The motor relay, which is incorporated in the ABS-ECU, is always off unless the
motor solenoid valve check is activated when the vehicle is started.
- The ABS-ECU activates the pump motor by turning on the ECU built-in motor relay
when the ABS is working.
DIAGNOSIS CODE SET CONDITIONS
These diagnosis codes will be set under the cases below.
Code No. C1266
- An open circuit has occurred to motor relay monitor.
- Motor is seized.
Code No. C1273
- At an initial start, the motor relay monitor judges the status of the motor relay
as "OFF," and the motor is driven.
Codes No. C1274
- When the motor relay monitor judges that the motor relay is "ON" while it is "OFF".
PROBABLE CAUSES
Current trouble
- Fusible link malfunction
- Battery failure
- Damaged harness wires and connectors
- Malfunction of the hydraulic unit assembly (integrated with ABS-ECU)
Past trouble
- Carry out diagnosis with particular emphasis on connector(s) or
wiring harness between the power supply circuit (+BM terminal) to the ABS-ECU motor
or earth circuit (GND1 and GND2 terminals). For diagnosis procedures, refer to How to treat
past trouble (GROUP 00 - How to Use Troubleshooting/Inspection Service Points
).
|
STEP 1. M.U.T.-III CAN bus diagnosis
|
|
Use M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
(1)Turn the ignition switch to the "ON" position.
|
|
(2)Drive the vehicle at 10 km/h or more.
|
|
(3)Erase the diagnosis code.
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check that the ABS warning lamp and brake warning lamp goes out.
|
|
(7)Check if the diagnosis code is set.
|
|
(8)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
Q.
Is diagnosis code No. C1266, C1273 or C1274 set?
|
|
Go to Step 3.
|
|
|
|
The procedure is complete.
|
|
|
|
STEP 3. Check the battery
|
|
Refer to GROUP 54A - Battery Test .
|
|
Q.
Is the auxiliary battery normal?
|
|
Go to Step 4.
|
|
|
|
Charge or replace the battery. Then go to Step 8.
|
|
|
|
STEP 4. Check the fusible link No.4
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. Measure the resistance at the ABS-ECU connector
|
|
(1)Remove the fusible link No.4.
|
|
(2)Check the ABS-ECU connector.
|
|
(3)Disconnect the connector and measure at the wiring harness side.
|
|
(4)Measure the resistance between +BM terminal and body earth. OK: No continuity
|
|
Q.
Is the check result normal?
|
|
Replace the fusible link No.4. Then go to Step 8.
|
|
|
|
The power supply circuit may be short. Repair the wiring harness wires or connectors
between the ABS-ECU connector +BM terminal and the fusible links, or replace the fusible
links. Then go to Step 8.
|
|
|
|
STEP 6. Measure the voltage at the ABS-ECU connector
|
|
(1)Check the ABS-ECU connector.
|
|
(2)Disconnect the connector and measure at the wiring harness side.
|
|
(3)Measure the voltage between +BM terminal and body earth. OK: Battery voltage
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
The power supply circuit may be open. Repair the wiring harness wires or connectors
between the ABS-ECU connector +BM terminal and the fusible links. Then go to Step 8
.
|
|
|
|
STEP 7. Check whether the diagnosis code is set again.
|
|
(1)Turn the ignition switch to the "ON" position.
|
|
(2)Drive the vehicle at 10 km/h or more.
|
|
(3)Erase the diagnosis code.
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check that the ABS warning lamp and brake warning lamp goes out.
|
|
(7)Check if the diagnosis code is set.
|
|
(8)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
Q.
Is diagnosis code No. C1266, C1273 or C1274 set?
|
|
Replace the hydraulic unit assembly (integrated with ABS-ECU) (Refer to ). Then
go to Step 8.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunctions ).
|
|
|
|
STEP 8. Check whether the diagnosis code is set again.
|
|
(1)Turn the ignition switch to the "ON" position.
|
|
(2)Drive the vehicle at 10 km/h or more.
|
|
(3)Erase the diagnosis code.
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check that the ABS warning lamp and brake warning lamp goes out.
|
|
(7)Check if the diagnosis code is set.
|
|
(8)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
Q.
Is diagnosis code No. C1266, C1273 or C1274 set?
|
|
Return to Step 1.
|
|
|
|
This diagnosis is complete.
|
|
|