|
When discarding the air bag modules
or a vehicle with SRS air bags, be sure to deploy the air
bags in advance as specified in the service procedure that
follows.
|
|
1.Move the vehicle to flat
and isolated spot.
|
|
2.
caution |
Disconnect the battery cable
connection, and wait for 60 seconds or more
before starting the work.
|
Disconnect the (-) and (+) terminals of
battery cable, and then remove the battery from the
vehicle.
|
|
3.Remove the Steering column
lower cover (Refer to GROUP 37 - Steering Column Shaft
Assembly ).
|
![](../../../img/52/ACF01435AD00ENG.png)
|
4.Remove the connection
between the clock spring connector (4-pin) and the harness
side connector (4-pin).
note |
Once disconnected from the
instrument panel wiring harness, both electrodes
of the clock spring connector short
automatically. This prevents the driver’s
air bag from accidental deployment caused by
static, etc.
|
|
![](../../../img/52/AC300381AD00ENG.png)
|
5.Obtain two suitable wires,
which are 6 m or longer, as deployment wires. Then connect
the wires at one end to short. 6.Touch the
vehicle’s body with bare hands to discharge static in
you.
|
![](../../../img/52/ACA00117AC00ENG.png)
|
7.Cut with a pliers, etc.
the instrument panel wiring harness shown in the figure of
the instructions, while the clock spring connector is
disconnected.
note |
The disconnection location
should be sufficiently away from the harness
side connector with consideration to the
expansion harness connection location upon
disconnections.
|
8.Connect the deployment wires on the two
instrument panel wiring harnesses disconnected, cover the
connection areas with insulator tape and then pull out the
deployment wires outside the vehicle. 9.Connect
the harness side connector connected with an expansion
harness to the clock spring connector.
|
![](../../../img/52/ACX01308AE00ENG.png)
|
10.
warning |
If the glass is scratched, the
glass may be shattered at deployment. Therefore,
cover with a vehicle cover to avoid
danger.
|
In order to suppress the operation sound as much as
possible, fully close all the door windows, close the doors,
and then cover the vehicle with a vehicle
cover. 11.
caution |
- Make sure that no one is present inside
or near the vehicle before deploying the
air bag.
- Immediately after the air bag
deployment, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the air bag module does not deploy,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the vehicle. Then, connect the wires
to the removed vehicle battery to deploy the air bag
module. 12.Discard the deployed air bag module
according to the disposal procedures (Refer to
).
|
|
1.Move the vehicle to flat
and isolated spot.
|
|
2.Disconnect the (-)
and (+) terminals of battery cable, and then remove
the battery from the vehicle.
|
|
3.Remove the
passenger’s (front) air bag module from the vehicle
(Refer to ).
|
![](../../../img/52/ACB04307AB00ENG.png)
|
4.Use the flat-tipped
screwdriver to pull out the locking button of floor harness
connector. After releasing the lock, disconnect the
connector.
note |
When the passenger’s
(front) air bag module connector is disconnected
from the inflator, the two pins of inflator
connector are automatically shorted. This
prevents the unintentional deployment of
passenger’s (front) air bags caused by the
static or others.
|
|
![](../../../img/52/AC103480AJ00ENG.png)
|
5.Connect the deployment
wires of 6 m or more to each of the two wiring harnesses of
special tool adapter harness (MB991885), and cover the
connection areas with insulation tape. Keep the other ends
of deployment wires connected to each other
(shorted).
note |
This prevents the
unintentional deployment of passenger’s
(front) air bag caused by the static or
others.
|
6.Connect the adapter harness to the
passenger’s (front) air bag module.
|
![](../../../img/52/ACE02523AB00ENG.png)
|
7.Connect the adapter
harness to the passenger’s (front) air bag module, and
then pull out the deployment wire to outside the
vehicle.
|
![](../../../img/52/ACX01308AE00ENG.png)
|
8.
warning |
If the glass is scratched, the
glass may be shattered at deployment. Therefore,
cover with a vehicle cover to avoid
danger.
|
In order to suppress the operation sound as much as
possible, fully close all the door windows, close the doors,
and then cover the vehicle with a vehicle
cover. 9.
caution |
- Make sure that no one is present inside
or near the vehicle before deploying the
air bag.
- Immediately after the air bag
deployment, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the air bag module does not deploy,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the vehicle. Then, connect the wires
to the removed vehicle battery to deploy the air bag
module. 10.Discard the deployed air bag module
according to the disposal procedures (Refer to
).
|
|
1.Move the vehicle to flat
and isolated spot.
|
|
2.Disconnect the (-)
and (+) terminals of battery cable, and then remove
the battery from the vehicle.
|
|
3.Remove the knee air bag
module (Refer to ).
|
![](../../../img/52/AC609126AF00ENG.png)
|
4.Use the flat-tipped
screwdriver to pull out the locking button of harness side
connector. After releasing the lock, disconnect the
connector.
note |
When the harness side
connector is disconnected from the inflator, the
two pins of inflator connector are automatically
shorted. This prevents the unintentional
deployment of knee air bag caused by the static
or others.
|
|
![](../../../img/52/AC103480AJ00ENG.png)
|
5.Connect the deployment
wires of 6 m or more to each of the two wiring harnesses of
special tool adapter harness (MB661885), and cover the
connection areas with insulation tape. Keep the other ends
of deployment wires connected to each other
(shorted).
note |
This prevents the
unintentional deployment of knee air bag caused
by the static or others.
|
|
![](../../../img/52/AC609127AC00ENG.png)
|
6.Connect the adapter
harness to the inflator, and then pull out the deployment
wire to outside the vehicle.
|
![](../../../img/52/ACX01308AE00ENG.png)
|
7.
warning |
If the glass is scratched, the
glass may be shattered at deployment. Therefore,
cover with a vehicle cover to avoid
danger.
|
In order to suppress the operation sound as much as
possible, fully close all the door windows, close the doors,
and then cover the vehicle with a vehicle
cover. 8.
caution |
- Make sure that no one is present inside
or near the vehicle before deploying the
air bag.
- Immediately after the air bag
deployment, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the air bag module does not deploy,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the vehicle. Then, connect the wires
to the removed vehicle battery to deploy the air bag
module. 9.Discard the deployed air bag module
according to the disposal procedures (Refer to
).
|
|
1.Move the vehicle to flat
and isolated spot.
|
|
2.Disconnect the (-)
and (+) terminals of battery cable, and then remove
the battery from the vehicle.
|
|
3.Remove the headlining
(Refer to GROUP 52A - Headlining ).
|
![](../../../img/52/AC506711AC00ENG.png)
|
4.Use the flat-tipped
screwdriver to pull out the locking button of curtain air
bag harness connector. After releasing the lock, disconnect
the connector.
note |
When the curtain air bag
module connector is disconnected from the
inflator, the two pins of inflator connector are
automatically shorted. This prevents the
unintentional deployment of curtain air bags
caused by the static or others.
|
|
![](../../../img/52/AC103480AJ00ENG.png)
|
5.Connect the deployment
wires of 6 m or more to each of the two wiring harnesses of
special tool adapter harness (MB661885), and cover the
connection areas with insulation tape. Keep the other ends
of deployment wires connected to each other
(shorted).
note |
This prevents the
unintentional deployment of curtain air bags
caused by the static or others.
|
|
![](../../../img/52/AC301520AH00ENG.png)
|
6.Connect the adapter
harness to the inflator, and then pull out the deployment
wire to outside the vehicle.
|
![](../../../img/52/ACX01308AE00ENG.png)
|
7.
warning |
If the glass is scratched, the
glass may be shattered at deployment. Therefore,
cover with a vehicle cover to avoid
danger.
|
In order to suppress the operation sound as much as
possible, fully close all the door windows, close the doors,
and then cover the vehicle with a vehicle
cover. 8.
caution |
- Make sure that no one is present inside
or near the vehicle before deploying the
air bag.
- Immediately after the air bag
deployment, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the air bag module does not deploy,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the vehicle. Then, connect the wires
to the removed vehicle battery to deploy the air bag
module. 9.Discard the deployed air bag module
according to the disposal procedures (Refer to
).
|
|
1.Move the vehicle to flat
and isolated spot.
|
|
2.Disconnect the (-)
and (+) terminals of battery cable, and then remove
the battery from the vehicle.
|
![](../../../img/52/AC507006AC00ENG.png)
|
3.Disconnect the connections
of the side-airbag module connector (2-pin: yellow) and the
floor harness connector (2-pin: yellow).
caution |
Make sure to deploy both
driver’s and front passenger’s
side-airbags.
|
note |
When the side-airbag module
connector is disconnected from the floor
harness, the two pins of side-airbag module
connector are automatically shorted. This
prevents the unintentional deployment of
side-airbags caused by the static or
others.
|
|
![](../../../img/52/AC100450AC00ENG.png)
|
4.Prepare two deployment
wires of 6 m or more, and keep the terminal at one end
connected to that of the other wire (shorted).
note |
This prevents the air bags
from unintentional deployment caused by
static.
|
5.
caution |
The following procedures are
intended to prevent the unintentional deployment
caused by the static. Therefore, make sure to
perform the procedures.
|
Touch the vehicle body with bare hands to release
the charged static.
|
![](../../../img/52/AC506974AC00ENG.png)
|
6.With the side-airbag
module connector disconnected, cut the floor harness using
nippers or similar tools. 7.Connect the deployment
wire to each of two cut wiring harnesses. After covering the
connection areas with insulation tape, pull out the
deployment wire to outside the vehicle. 8.Connect
the floor harness, to which the deployment wire is
connected, to the side-airbag module connector.
|
![](../../../img/52/ACX01308AE00ENG.png)
|
9.
warning |
If the glass is scratched, the
glass may be shattered at deployment. Therefore,
cover with a vehicle cover to avoid
danger.
|
In order to suppress the operation sound as much as
possible, fully close all the door windows, close the doors,
and then cover the vehicle with a vehicle
cover. 10.
caution |
- Make sure that no one is present inside
or near the vehicle before deploying the
air bag.
- Immediately after the air bag
deployment, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the air bag module does not deploy,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the vehicle. Then, connect the wires
to the removed vehicle battery to deploy the side-airbag
module. 11.Discard the deployed air bag module
according to the disposal procedures (Refer to
).
|
|
1.
caution |
Disconnect the battery cable
connection, and wait for 60 seconds or more
before starting the work.
|
Disconnect the (-) and (+) terminals of
battery cable, and then remove the battery from the
vehicle.
|
|
2.
caution |
When the connector is
disconnected, the two pins of air bag module are
automatically shorted to prevent the
unintentional deployment caused by the static or
others. However, in preparation for the
accidental deployment, store the air bag module
on a flat place with the deployment surface
facing upward. Also, do not put anything on
it.
|
Remove the driver’s air bag module from the
vehicle (Refer to ).
|
![](../../../img/52/AC905252AC00ENG.png)
|
3.Cut the part shown to
connect the adapter harness (Special tool: MB991885) to the
driver’s airbag module connector.
|
![](../../../img/52/AC103480AJ00ENG.png)
|
4.Connect the deployment
wires of 6 m or more to each of the two wiring harnesses of
special tool adapter harness (MB991885), and cover the
connection areas with insulation tape. Keep the other ends
of deployment wires connected to each other
(shorted).
note |
This prevents the
unintentional activation of inflator caused by
the static or others.
|
5.Connect the adapter harness to the
driver’s air bag module. 6.To the torx screw
installation hole located at the backside of air bag module,
tie a thick wire for fixing the wheel.
|
![](../../../img/52/AC100482AC00ENG.png)
|
7.Pass the deployment wire
connected to the air bag module underneath the old tyre with
wheel. Then, fix the air bag module with deployment surface
facing upward using the wire which is tied to the
bolt.
|
![](../../../img/52/ACX00610AD00ENG.png)
|
8.Place three old tyres
without wheel onto the tyre to which the air bag module is
fixed.
|
![](../../../img/52/ACX01313AD00ENG.png)
|
9.
caution |
- Make sure that no one is present near
the air bag module before deploying the
air bag.
- Immediately after the air bag
deployment, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the air bag module does not deploy,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the air bag module. Then, connect
the wires to the removed vehicle battery to deploy the air
bag module. 10.Discard the deployed air bag module
according to the disposal procedures (Refer to
).
|
|
1.
caution |
Before starting the work, wait
for 60 seconds or more after the disconnection
of the battery cable. (Refer to the item 5
of Service Precautions.)
|
Disconnect the (-) and (+) terminals of
battery cable, and then remove the battery from the
vehicle.
|
|
2.
caution |
When the connector is
disconnected, the two pins of air bag module are
automatically shorted to prevent the
unintentional deployment caused by the static or
others. However, in preparation for the
accidental deployment, store the air bag module
on a flat place with the deployment surface
facing upward. Also, do not put anything on
it.
|
Remove the passenger’s (front) air bag module
from the vehicle (Refer to ).
|
![](../../../img/52/AC103480AJ00ENG.png)
|
3.Connect the deployment
wires of 6 m or more to each of the two wiring harnesses of
special tool adapter harness (MB991885), and cover the
connection areas with insulation tape. Keep the other ends
of deployment wires connected to each other
(shorted).
note |
This prevents the
unintentional activation of inflator caused by
the static or others.
|
4.Connect the adapter harness to the
passenger’s (front) air bag module.
|
![](../../../img/52/AC300520AC00ENG.png)
|
5.Pass a thick wire through
the hole of air bag module bracket. Then, with the air bag
module deployment surface facing upward, fix the module to
the old tyre with wheel.
|
![](../../../img/52/ACX00611AD00ENG.png)
|
6.Place three old tyres
without wheel onto the tyre to which the air bag module is
fixed. Then, tie and fix all the tyres with rope (4
positions).
note |
The passenger’s (front)
air bag has a larger deployment volume than the
driver’s air bag. Therefore, it is
necessary to tie the tyres with rope.
|
|
![](../../../img/52/ACX01315AD00ENG.png)
|
7.
caution |
- Make sure that no one is present near
the air bag module before deploying the
air bag.
- Immediately after the air bag
deployment, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the air bag module does not deploy,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the air bag module. Then, connect
the wires to the removed vehicle battery to deploy the air
bag module. 8.Discard the deployed air bag module
according to the disposal procedures (Refer to
).
|
|
1.
caution |
Disconnect the battery cable
connection, and wait for 60 seconds or more
before starting the work.
|
Disconnect the (-) and (+) terminals of
battery cable, and then remove the battery from the
vehicle.
|
|
2.
caution |
When the connector is
disconnected, the two pins of air bag module are
automatically shorted to prevent the
unintentional deployment caused by the static or
others. However, in preparation for the
accidental deployment, store the air bag module
on a flat place with the deployment surface
facing upward. Also, do not put anything on
it.
|
Remove the knee air bag module from the vehicle
(Refer to ).
|
![](../../../img/52/AC103480AJ00ENG.png)
|
3.Connect the deployment
wires of 6 m or more to each of the two wiring harnesses of
special tool adapter harness (MB991885), and cover the
connection areas with insulation tape. Keep the other ends
of deployment wires connected to each other
(shorted).
note |
This prevents the
unintentional activation of inflator caused by
the static or others.
|
4.Connect the adapter harness to the knee air
bag module.
|
![](../../../img/52/AC609239AC00ENG.png)
|
5.Pass the thick wire
through the hole of air bag module mounting bracket. When,
with the air bag module deployment surface facing upward,
fit the module to the old tyre with wheel.
|
![](../../../img/52/ACX00610AD00ENG.png)
|
6.Place three old tyres
without wheel onto the tyre to which the air bag module is
fixed.
|
![](../../../img/52/ACX01313AD00ENG.png)
|
7.
caution |
- Make sure that no one is present near
the air bag module before deploying the
air bag.
- Immediately after the air bag
deployment, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the air bag module does not deploy,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the air bag module. Then, connect
the wires to the removed vehicle battery to deploy the air
bag module. 8.Discard the deployed air bag module
according to the disposal procedures (Refer to
).
|
|
1.
caution |
Before starting the work, wait
for 60 seconds or more after the disconnection
of the battery cable. (Refer to the item 5
of Service Precautions.)
|
Disconnect the (-) and (+) terminals of
battery cable, and then remove the battery from the
vehicle.
|
|
2.
caution |
When the connector is
disconnected, the two pins of inflator are
automatically shorted to prevent the
unintentional activation caused by the static or
others. However, in preparation for the
accidental activation, store the air bag module
on a flat place with the activation surface
facing upward. Also, do not put anything on
it.
|
Remove the headlining (Refer to GROUP 52A -
Headlining ).
|
![](../../../img/52/AC506711AC00ENG.png)
|
3.Use the flat-tipped
screwdriver to pull out the locking button of curtain air
bag harness connector. After releasing the lock, disconnect
the connector.
note |
When the harness connector is
disconnected from the inflator, the two pins of
inflator connector are automatically shorted.
This prevents the unintentional activation of
inflator caused by the static or
others.
|
|
![](../../../img/52/AC303536AB00ENG.png)
|
4.Cut the inflator from the
air bag as shown in the figure using a cutter or a similar
tool.
|
![](../../../img/52/AC103480AJ00ENG.png)
|
5.Connect the deployment
wires of 6 m or more to each of the two wiring harnesses of
special tool adapter harness (MB991885), and cover the
connection areas with insulation tape. Keep the other ends
of deployment wires connected to each other
(shorted).
note |
This prevents the
unintentional activation of inflator caused by
the static or others.
|
|
![](../../../img/52/AC303641AD00ENG.png)
|
6.Feed a thick wire through
the bracket of the inflator, and connect it to an old tyre
with a wheel. 7.Connect the adapter harness to the
inflator connector.
|
![](../../../img/52/ACX00611AD00ENG.png)
|
8.Place the tyre to which
the inflator is fixed onto the two stacked tyres. Then,
place 1 or more old tyres without wheel onto the stacked
tyres, and tie and fix all the tyres with rope. (4
positions)
|
![](../../../img/52/ACX01315AD00ENG.png)
|
9.
caution |
- Make sure that no one is present near
the inflator before the
activation.
- Immediately after the inflator
activation, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the inflator does not activate,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the inflator. Then, connect the
wires to the removed vehicle battery to activate the
inflator. 10.Discard the activated inflator
according to the disposal procedures (Refer to ).
|
|
1.
caution |
Before starting the work, wait
for 60 seconds or more after the disconnection
of the battery cable. (Refer to the item 5
of Service Precautions.)
|
Disconnect the (-) and (+) terminals of
battery cable, and then remove the battery from the
vehicle.
|
|
2.Remove the front seat
assembly incorporated in side-airbag from the vehicle (GROUP
52A - Front Seat Assembly ).
|
|
3.
caution |
When the connector is
disconnected, the two pins of side-airbag module
are automatically shorted to prevent the
unintentional deployment caused by the static or
others. However, in preparation for the
accidental deployment, store the air bag module
on a flat place with the deployment surface
facing upward. Also, do not put anything on
it.
|
Remove the side-airbag module from the front seat
assembly incorporated in the side-airbag (Refer to ).
|
![](../../../img/52/AC100450AC00ENG.png)
|
4.Prepare two deployment
wires of 6 m or more, and keep the terminal at one end
connected to that of the other wire (shorted).
note |
This prevents the air bags
from unintentional deployment caused by
static.
|
5.
caution |
The following procedures are
intended to prevent the unintentional deployment
caused by the static. Therefore, make sure to
perform the procedures.
|
Touch the vehicle body with bare hands to release
the charged static.
|
![](../../../img/52/AC406391AD00ENG.png)
|
6.Cut off the side-airbag
module wiring harness connector from the wiring harness with
nippers. Connect the deployment wire to each of the two cut
wiring harnesses, and cover the connection areas with
insulation tape.
|
![](../../../img/52/AC300990AJ00ENG.png)
|
7.Pass the deployment wire
under the tyre with wheel, and connect it to the side-airbag
module connector. 8.Install a surplus nut to the
side-airbag module bolt. Then, tie a thick wire for fixing
the wheel to the bolt. Fix the side-airbag module to the
wheel of old tyre with the module deployment surface facing
upward.
|
![](../../../img/52/ACX00611AD00ENG.png)
|
9.Place three old tyres
without wheel onto the tyre to which the side-airbag module
is fixed. Then, tie and fix all the tyres with rope. (4
positions)
|
![](../../../img/52/ACX01315AD00ENG.png)
|
10.
caution |
- Make sure that no one is present near
the air bag module before deploying the
air bag.
- Immediately after the air bag
deployment, the inflator is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the air bag module does not deploy,
consult with your distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the air bag module. Then, connect
the wires to the removed vehicle battery to deploy the air
bag module. 11.Discard the deployed air bag module
according to the disposal procedures (Refer to
).
|
|
After deployment and operation, the
air bag module and seat belt pre-tensioner should be
disposed of in the same manner as any other scrap parts,
adhering to local laws and/or legislation. Observe the
following precautions during air bag or seat belt
pre-tensioner disposal:
|
|
1.Immediately after the air
bag deployment, the inflator is extremely hot. Thus, before
handling, leave the inflator for 30 minutes or more to
cool.
|
|
2.Do not pour water or oil
onto the deployed air bag module.
|
|
3.To the deployed air bag
module, substances that irritate eyes and skin may be
deposited. Therefore, wear gloves and protective glasses
when handling the module. When the substance comes in
contact with eyes or skin, flush with a large amount of
water.
|
|
4.Place the air bag module
in the sturdy plastic bag, and seal the bag for
disposal.
|
|
5.After the work, be sure to
wash your hands with water.
|