Code No.B1707:
Flasher open
COMMENTS ON TROUBLE SYMPTOM
When the turn-signal lamp bulb is blown, or connector(s) or wiring harness between the
ETACS-ECU, the turn-signal lamp which does not illuminate and body earth is defective, the ETACS-ECU
set diagnosis code No.B1707.
PROBABLE CAUSES
- Malfunction of the turn-signal lamp bulb
- Malfunction of the headlamp assembly
- Malfunction of the rear combination lamp assembly
- Malfunction of the ETACS-ECU
- Damaged harness wires and connectors
|
STEP 1. Confirm which turn-signal lamp is defective.
|
|
Q.
Which turn-signal lamp fails to illuminate correctly?
|
|
Front turn-signal lamp : Go to Step 2.
|
|
|
|
Side turn-signal lamp : Go to Step 7.
|
|
|
|
Rear turn-signal lamp : Go to Step 12.
|
|
|
|
STEP 2. Check the bulb(s) of the front turn-signal lamps.
|
|
Check the bulb(s) of the defective lamp.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Replace the bulb(s) of the defective lamp. Go to Step 17.
|
|
|
|
STEP 3. Resistance measurement at the headlamp assembly (turn: LH)
connector or headlamp assembly (turn: RH) connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Resistance measurement between the defective lamp connector terminal and body earth.
- Measure the resistance between the headlamp assembly (turn: LH) connector
(E terminal) and the body earth.
- Measure the resistance between the headlamp assembly (turn: RH) connector (E terminal)
and the body earth.
OK: Continuity exists (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Check of open circuit in body E line between headlamp assembly
(turn: LH) connector or headlamp assembly (turn: RH) connector and body earth.
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to use Troubleshooting/inspection Service Points - How to Cope with Intermittent
Malfunction ). Go to Step 17.
|
|
|
|
Repair the connector(s) or wiring harness. Go to Step 17.
|
|
|
|
STEP 5. Check of open circuit in TURN LH or TURN RH line between headlamp
assembly (turn: LH) connector or headlamp assembly (turn: RH) connector and ETACS-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Repair the connector(s) or wiring harness. Go to Step 17.
|
|
|
|
STEP 6. Retest the system.
|
|
Check that the front turn-signal lamps illuminate normally.
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to use Troubleshooting/inspection Service Points - How to Cope with Intermittent
Malfunction ). Go to Step 17.
|
|
|
|
Replace the front turn-signal lamp. Go to Step 17.
|
|
|
|
STEP 7. Check the bulb(s) of side turn-signal lamps.
|
|
Check the bulb(s) of the defective lamp.
|
|
Q.
Is the check result normal?
|
|
Go to Step 8.
|
|
|
|
Replace the bulb(s) of the defective lamp. Go to Step 17.
|
|
|
|
STEP 8. Resistance measurement at the door mirror assembly (LH) connector
or door mirror assembly (RH) connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Resistance measurement between the defective lamp connector terminal and body earth.
- Measure the resistance between the door mirror assembly (LH) connector (earth
terminal) and the body earth.
- Measure the resistance between the door mirror assembly (RH) connector (earth terminal)
and the body earth.
OK: Continuity exists (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
Go to Step 10.
|
|
|
|
Go to Step 9.
|
|
|
|
STEP 9. Check of open circuit in body earth line between door mirror
assembly (LH) connector or door mirror assembly (RH) connector and body earth.
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to use Troubleshooting/inspection Service Points - How to Cope with Intermittent
Malfunction ).
|
|
|
|
Repair the connector(s) or wiring harness. Go to Step 17.
|
|
|
|
STEP 10. Check of open circuit in TURN LH or TURN RH line between
door mirror assembly (LH) connector or door mirror assembly (RH) connector and ETACS-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 11.
|
|
|
|
Repair the connector(s) or wiring harness. Go to Step 17.
|
|
|
|
STEP 11. Retest the system.
|
|
Check that the side turn-signal lamps illuminate normally.
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to use Troubleshooting/inspection Service Points - How to Cope with Intermittent
Malfunction ). Go to Step 17.
|
|
|
|
Replace the side turn-signal lamp assembly (Refer to GROUP 51 - Door
Mirror ). Go to Step 17.
|
|
|
|
STEP 12. Check the bulb(s) of rear turn-signal lamps.
|
|
Check the bulb(s) of the defective lamp.
|
|
Q.
Is the check result normal?
|
|
Go to Step 13.
|
|
|
|
Replace the bulb(s) of the defective lamp. Go to Step 17.
|
|
|
|
STEP 13. Resistance measurement at the rear combination lamp (turn:
LH) or rear combination lamp (turn: RH) connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Resistance measurement between the defective lamp connector terminal and body earth.
- Measure the resistance between the side rear combination lamp (turn: LH)
connector (earth terminal) and the body earth.
- Measure the resistance between the side rear combination lamp (turn: RH) connector
(earth terminal) and the body earth.
OK: Continuity exists (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
Go to Step 15.
|
|
|
|
Go to Step 14.
|
|
|
|
STEP 14. Check of open circuit in body earth line between rear combination
lamp (turn: LH) connector or rear combination lamp (turn: RH) connector and body earth.
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to use Troubleshooting/inspection Service Points - How to Cope with Intermittent
Malfunction ). Go to Step 17.
|
|
|
|
Repair the connector(s) or wiring harness. Go to Step 17.
|
|
|
|
STEP 15. Check of open circuit in TURN LH or TURN RH line between
rear combination lamp (turn: LH) connector or rear combination lamp (turn: RH) connector and
ETACS-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 16.
|
|
|
|
Repair the connector(s) or wiring harness. Go to Step 17.
|
|
|
|
STEP 16. Retest the system.
|
|
Check that the rear turn-signal lamps illuminate normally.
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to use Troubleshooting/inspection Service Points - How to Cope with Intermittent
Malfunction ). Go to Step 17.
|
|
|
|
Replace the rear combination lamp. Go to Step 17.
|
|
|
|
STEP 17. Check whether the diagnosis code is set again.
|
|
Check if diagnosis code No.B1707 is set in the ETACS-ECU.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the ETACS-ECU (Refer to ETACS, ETACS-ECU ).
|
|
|
|
The procedure is complete.
|
|
|