CHECK PROCEDURE FOR EACH MULTI INFORMATION DISPLAY SCREEN <COLOUR LIQUID CRYSTAL DISPLAY TYPE>


caution When there are TV towers, substations, or broadcasting stations which emit strong radio waves in proximity, on rare occasions, a warning is displayed on the multi information screen for a few seconds. This is caused by the reception of strong radio waves, and there is no functional problem.

WARNING SCREEN


When malfunctions occur to the vehicle, the following warning screens are displayed. If these screens are not displayed normally or if they continue to be displayed even after the factor is eliminated, take measures according to the action procedure.
Display content
 Message
 Factor
 Action procedure


LOW OIL PRESSURE
 Displayed when there is a malfunction to the engine oil circulation system.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the oil pressure. (Refer to GROUP 12 - On-vehicle Service .) Then if the oil pressure is normal, perform the troubleshooting for the engine. (Refer to GROUP 13A - Trouble Symptom Chart .)


ENGINE OVERHEATING STOP SAFELY
 Displayed when overheated.
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the engine. Refer to GROUP 13A - Trouble Symptom Chart .


REMOVE WATER IN SEPARATOR
 Displayed when the water that exceeds the permissible limit is stored in the fuel filter.
 If the warning screen is not displayed normally or if the screen continues to be displayed, drain water from the fuel filter. Refer to GROUP 13C - On-vehicle Service .


CHARGING SYSTEM SERVICE REQUIRED
 Displayed when there is a malfunction to the charging system.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the charging system. Refer to GROUP 16 - On-vehicle Service - Output current test and Regulated voltage test .


TRANSMISSION OVERHEATING SLOW DOWN
 Displayed when the transmission oil temperature becomes high.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the A/T diagnosis code. Refer to GROUP 23A - Diagnosis Code Chart .


TRANSMISSION SERVICE REQUIRED
 Displayed when there is a malfunction to the A/T.


PRESS BRAKE PEDAL SHIFT TO N POSITION
 The selector lever is shifted from the "N"(NEUTRAL) position to the "D"(DRIVE) position during shifting process between "4HLc" <=> "4LLc".
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the 4WD system. Refer to GROUP 23A - Trouble Symptom Chart .


TRANSFER 4HLc<=>4LLc NOT AVAILABLE
 There is a fault in the A/T. Shifting between a "2H" <=> "4H" <=> "4HLc" selection can be made, but when the drive mode-selector is in "4LLc" the transfer mode cannot be switched.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the A/T diagnosis code. Refer to GROUP 23A - Diagnosis Code Chart .


4WD SYSTEM SERVICE REQUIRED
 Displayed when there is a malfunction to the electronically-controlled 4WD system.


TEMPORARILY NOT AVAILABLE
 Displayed when the off road mode is inactive temporarily.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the A/T diagnosis code. Refer to GROUP 23A - Diagnosis Code Chart .


NOT AVAILABLE WITH 2H/4H
 The Off Road mode will not be available even if the Off Road mode selector is pressed because the drive mode-selector is in "2H" or "4H".


NOT AVAILABLE WITH R/D LOCK
 The Off Road mode will not be available even if the Off Road mode selector is pressed because the rear differential lock is ON.


R/D LOCK SERVICE REQUIRED
 Displayed when the rear differential lock system is defective.
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the rear differential lock. Refer to GROUP 23A - Diagnosis Code Chart .


STOP TO OPERATE R/D LOCK
 Displayed when the rear differential lock system is defective.


BRAKE SYSTEM SERVICE REQUIRED
 Displayed when the brake fluid amount is insufficient or a malfunction occurs to the brake device.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the brake fluid or brake device. Refer to GROUP 35A - On-vehicle Service .


ABS SERVICE REQUIRED
 Displayed when a malfunction occurs to the anti-skid braking system (ABS).
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the ABS or ASTC. Refer to GROUP 35B - Trouble Symptom Chart <ABS> or GROUP 35C - Trouble Symptom Chart <ASTC>.


ASTC SYSTEM SERVICE REQUIRED
 Displayed when there is a malfunction to the ASTC or Hill Start Assist (HSA).
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the ASTC. Refer to GROUP 35C - Trouble Symptom Chart .


BRAKE TEMPERATURE HIGH
 Displayed when the brake system temperature is too high.


HDC TEMPORARILY NOT AVAILABLE
 Displayed when the hill descent control is inactive temporarily.
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the ASTC. Refer to GROUP 35C - Trouble Symptom Chart .


STOP TO OPERATE HDC
 The Hill Descent Control (HDC) cannot be set to ON (stand by) because the vehicle speed is 20 km/h or more.


HDC NOT AVAILABLE WITH R/D LOCK
 The Hill Descent Control (HDC) cannot be set to ON (stand by) because the rear differential lock is ON.


-
 Displayed when your vehicle may collide with a vehicle-traveling-ahead.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the FCM diagnosis code. Refer to GROUP 35C - Diagnosis Code Chart .


FCM BRAKE ACTIVATED
 Displayed after the FCM braking function of the FCM has been activated.


FCM TEMPORARILY NOT AVAILABLE
 Displayed when the FCM is inactive temporarily.


FCM SERVICE REQUIRED
 Displayed when the FCM is defective.


FCM RADAR BLOCKED
 Displayed when the FCM is defective.


FCM NOT AVAILABLE WITH 4LLc
  • When the FCM is ON, if the drive mode selector of 4WD system is set to "4LLc", the FCM will be switched to OFF automatically.
  • When the FCM is OFF, the FCM will not be switched to ON even if the FCM and Ultrasonic misacceleration Mitigation System (UMS) ON/OFF switch is pressed because the drive mode-selector of 4WD system is in "4LLc".

 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the FCM. Refer to GROUP 35C - Trouble Symptom Chart .


FCM NOT AVAILABLE WITH R/D LOCK
  • When the FCM is ON, if the rear differential lock switch is set to ON, the FCM will be switched to OFF automatically.
  • When the FCM is OFF, even if the FCM and Ultrasonic misacceleration Mitigation System (UMS) ON/OFF switch is pressed, the FCM will not be switched to ON because the rear differential lock switch is ON.

 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the FCM. Refer to GROUP 35C - Trouble Symptom Chart .


FCM NOT AVAILABLE WITH HDC
  • When the FCM is ON, if the Hill Descent Control is set to ON, the FCM will be switched to OFF automatically.
  • When the FCM is OFF, even if the FCM and Ultrasonic misacceleration Mitigation System (UMS) ON/OFF switch is pressed, the FCM will not be switched to ON because the Hill Descent Control operates.

 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the FCM. Refer to GROUP 35C - Trouble Symptom Chart .


UMS TEMPORARILY NOT AVAILABLE
 Displayed when only the ultrasonic misacceleration mitigation system (FRONT) is disabled temporarily as the forward distance warning sensor has received noise.
 If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the ultrasonic misacceleration mitigation system (Refer to ).
UMS (FRONT) TEMPORARILY NOT AVAILABLE
 Displayed when only the ultrasonic misacceleration mitigation system (REAR) is disabled temporarily as the back distance warning sensor has received noise.
UMS (REAR) TEMPORARILY NOT AVAILABLE
 Displayed when the ultrasonic misacceleration mitigation system (front or rear) is disabled temporarily as the forward/back distance warning sensor has received noise, the clearance warning control unit is too hot or cold, or the forward/back distance warning sensor is out of their operation temperature range.


UMS SERVICE REQUIRED
 Displayed when only the ultrasonic misacceleration mitigation system (FRONT) is disabled due to an open circuit in the forward distance warning sensor wires.
 If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the ultrasonic misacceleration mitigation system (Refer to ).
UMS (FRONT) SERVICE REQUIRED
 Displayed when only the ultrasonic misacceleration mitigation system (REAR) is disabled due to an open circuit in the back distance warning sensor wires.
UMS (REAR) SERVICE REQUIRED
 Displayed when the ultrasonic misacceleration mitigation system (front or rear) is disabled temporarily as the forward/back distance warning sensor wires are broken (open circuit), or the clearance warning control unit fails.


UMS NOT AVAILABLE WITH 4LLc
  • When the ultrasonic misacceleration mitigation system is ON, if the drive mode-selector of 4WD system is set to "4LLc", the ultrasonic misacceleration mitigation system will be switched to OFF automatically.
  • When the ultrasonic misacceleration mitigation system is OFF, even if the FCM and ultrasonic misacceleration mitigation system (UMS) ON/OFF switch is pressed, the ultrasonic misacceleration mitigation system will not be switched to ON because the drive mode selector of 4WD system is in "4LLc".

 If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the ultrasonic misacceleration mitigation system (Refer to ).


UMS NOT AVAILABLE WITH R/D LOCK
  • When the ultrasonic misacceleration mitigation system is ON, if the rear differential lock switch is set to ON, the ultrasonic misacceleration mitigation system will be switched to OFF automatically.
  • When the ultrasonic misacceleration mitigation system is OFF, even if the FCM and ultrasonic misacceleration mitigation system (UMS) ON/OFF switch is pressed, the ultrasonic misacceleration mitigation system will not be switched to ON because the rear differential lock switch is ON.

 If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the ultrasonic misacceleration mitigation system (Refer to ).


UMS NOT AVAILABLE WITH HDC
  • When the ultrasonic misacceleration mitigation system is ON, if the Hill Descent Control is set to ON, the ultrasonic misacceleration mitigation system will be switched to OFF automatically.
  • When the ultrasonic misacceleration mitigation system is OFF, even if the FCM and ultrasonic misacceleration mitigation system (UMS) ON/OFF switch is pressed, the ultrasonic misacceleration mitigation system will not be switched to ON because the Hill Descent Control operates.

 If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the ultrasonic misacceleration mitigation system (Refer to ).


RELEASE PARKING BRAKE
 Displayed if vehicle is driven with the parking brake engaged.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the parking brake. Refer to GROUP 36 - On-vehicle Service .


PARKING BRAKE SERVICE REQUIRED
 Displayed when a malfunction occurs to the electric parking break.
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the electric parking brake. Refer to GROUP 36 - Trouble Symptom Chart .


PARKING BRAKE TEMPORARILY NOT AVAILABLE
 Displayed when the electric parking break is inactive temporarily.


PRESS BRAKE PEDAL TO RELEASE
 You try to release the electric parking brake switch without depressing the brake pedal.


KEY BATTERY LOW
 Displayed when the keyless operation key battery is running low.
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the KOS. Refer to GROUP 42B - Diagnosis code chart .


KEY NOT DETECTED
 Displayed if carrying a keyless operation key with different ID code or the keyless operation key is outside the operative range.


KEY STILL IN VEHICLE
 Displayed when the keyless operation key take-out monitoring function or keyless operation key confinement prevention function is in operation.


CHECK DOORS
 Displayed when the door ajar prevention function is in operation.


KEYLESS OPERATION SYSTEM SERVICE REQUIRED
 Displayed when there is a malfunction to KOS.


KEY NOT DETECTED INSERT KEY INTO KEY SLOT
 Displayed when the keyless operation key cannot be detected.


REMOVE KEY FROM KEY SLOT
 Displayed when the key is not removed from the key slot located in the glove box.


-
 Displayed when the lock/unlock switch of front door outside handle is pressed while in the power mode other than OFF.


-
 Displayed when the driver’s door is open while in the power mode other than OFF.
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the OSS. Refer to GROUP 42B - Diagnosis code chart .


IMMOBILIZER SYSTEM SERVICE REQUIRED
 Displayed when a malfunction occurs to the immobilizer system.


PUSH ENGINE SWITCH WHILE TURNING STEERING WHEEL
 Displayed when the steering lock is in operation.


STEERING LOCK SERVICE REQUIRED
 Displayed when a malfunction occurs to the steering lock.


SHIFT TO P POSITION
 Displayed when the engine is stopped while the selector lever is in other than P position.
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the OSS. Refer to GROUP 42B - Trouble Symptom Chart .


STEERING WHEEL UNLOCKED
 Displayed when the steering lock is not in operation.


ELECTRICAL SYSTEM SERVICE REQUIRED
 Displayed when a malfunction occurs to the power supply system.


PRESS BRAKE PEDAL TO START ENGINE
 Displayed when the engine switch is pressed without the brake pedal depressed at starting the engine.


AIRBAG SYSTEM SERVICE REQUIRED
 Displayed when there is a malfunction to the SRS air bag or to the pre-tensioner mechanism.
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the SRS air bag/pre-tensioner mechanism warning lamp. Refer to GROUP 52B - Trouble symptom chart .


TURN OFF LIGHTS
 Displayed with the sounding of buzzer when the driver’s door is opened with the ignition switch at the LOCK (OFF) or ACC position and the lighting switch at the tail or head position.
 If the lighting monitor warning buzzer is not being sounded, perform the troubleshooting for the lighting monitor warning buzzer. Refer to .


FASTEN SEAT BELT
 Displayed when the ignition switch is turned ON without the driver’s and passenger’s seat belt fastened.
 If the warning screen is not displayed normally or if the screen continues to be displayed, perform the troubleshooting for the seat belt reminder warning lamp. Refer to .


FUEL SYSTEM SERVICE REQUIRED
 Displayed when there is a malfunction to the fuel system.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the combination meter diagnosis code. Refer to .


REFUEL
 Displayed when the remaining fuel amount is small.
 If the warning screen is not displayed normally or if the screen continues to be displayed, refuel immediately.


POSSIBLE ICY ROADS
 Displayed with the sounding of buzzer when the ambient temperature is 3 °C or less.
 If the warning buzzer does not sound when the combination meter displays 3 °C, perform the troubleshooting for the freeze warning buzzer. Refer to .


-
 If any of the doors or tailgate is not closed completely, the location of the ajar door is displayed with the sounding of buzzer.
 If the door ajar warning buzzer does not sound, perform the troubleshooting for the door ajar warning buzzer. Refer to .


LED HEADLIGHT SERVICE REQUIRED
 The LED type headlamps are defective.
 If the warning screen is not displayed normally or if the screen continues to be displayed, troubleshooting for the headlamps. Refer to .


BSW TEMPORARILY NOT AVAILABLE
 Displayed when the blind spot warning sensor is temporarily not available for some reason such as the environmental condition or increase of the sensor temperature.
 If the warning screen is not displayed normally or if the screen continues to be displayed, troubleshooting for the BSW. Refer to .


BSW SERVICE REQUIRED
 Displayed when the blind spot warning is defective.

OTHER SCREENS


The screen displays the operation state of each system, periodic checkup timing, or timing for taking a rest during driving. If the screen display differs from the actual system operation state or if the screen is not displayed at the set timing, take measures according to the action procedure.
Display content
 Message
 Factor
 Action procedure
a

 -
 Displayed in accordance with operation state of the drive mode-selector.

  1. Drive mode.
  2. "ROCK" mode is selected.
  3. "MUD/SNOW" mode is selected.
  4. "SAND" mode is selected.
  5. "GRAVEL" mode is selected.
 If the drive mode-selector position and screen do not agree with each other, perform the troubleshooting for the 4WD. Refer to GROUP 23A - Trouble symptom chart .
b

 -
c

 -
d

 -
e

 -


-
 Displayed when the FCM is deactivated.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the FCM diagnosis code. Refer to GROUP 35C - Diagnosis Code Chart .
Displayed when the UMS is deactivated.
 If the warning screen is not displayed normally or if the screen continues to be displayed, carry out the troubleshooting for the ultrasonic misacceleration mitigation system (Refer to ).
-
 ACCELERATION PEDAL PRESSED
 Displayed when the system determines that the accelerator pedal is depressed more deeply than necessary during driving forwards or backwards at approx. 10 km/h.


UMS ACTIVATED
 Displayed when the ultrasonic misacceleration mitigation system is activated.


FCM NEAR
 Displayed when the FCM warning timing is switched to "NEAR."
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the FCM diagnosis code. Refer to GROUP 35C - Diagnosis Code Chart .


FCM MIDDLE
 Displayed when the FCM warning timing is switched to "MIDDLE."


FCM FAR
 Displayed when the FCM warning timing is switched to "FAR."


-
 Displayed when the reversing sensor system detect an obstruction.
 If the warning screen is not displayed normally or if the screen continues to be displayed, check the reversing sensor diagnosis code. Refer to .


ROUTINE MAINTENANCE REQUIRED
 Displayed when the set period elapses.
 -


REST REMINDER
 Displayed when the set time elapses.
 -