Code No. B1762
IOD fuse not seated fully
Code No. B1765 ECU fuse
caution |
Before replacing the ECU,
ensure that the power supply circuit, the earth circuit and the
communication circuit are normal.
|
TROUBLE JUDGEMENT
- When voltage at the power supply fuses (fuse Nos. 25
and 26) drops below 5 V with the ignition switch ON and ACC OFF signal is
detected for 500 milliseconds,
the ETACS-ECU sets diagnosis code No. B1762.
- When voltage at the ECU fuse (fuse No. 26) drops below 5 V with the
ignition switch
ON and ACC ON signal is detected for 500 milliseconds, the ETACS-ECU sets
diagnosis code No.
B1765.
PROBABLE CAUSES
- Malfunction of fuse No. 25
- Malfunction of fuse No. 26
- Malfunction of the ETACS-ECU
- Malfunction of the KOS&OSS-ECU <Vehicles with
KOS>
- Damaged harness wires and connectors
|
STEP 1. Check the power supply fuses (fuse Nos. 25 and 26)
|
![](../../../img/54/AC706261AB00ENG.png)
|
Check the power supply fuses (fuse Nos. 25 and
26). (Refer to GROUP 00 - How
to Use Troubleshooting/Inspection Service Points - Inspection
Service Points
for a Blown Fuse .)
Q.
Is the fuse in good condition?
Go to Step 2.
Then go to Step
5.
|
|
STEP 2. Check of short to power supply, short to earth, and open
circuit
in ETACS +B line between fusible link and ETACS-ECU
connector
|
|
Q.
Is the check result normal?
|
|
YES <vehicles with KOS> : Go to Step
3.
|
|
|
|
YES <vehicles without KOS> : Go to Step
4.
|
|
|
|
NO : Repair the connector(s) or
wiring harness. Then go to Step 5.
|
|
|
|
STEP 3. Check the M.U.T.-III Diagnosis code for other
systems
|
|
Check whether the KOS&OSS-ECU sets a
diagnosis code.
|
|
Q.
Is the diagnosis code set?
|
|
Diagnose the KOS&OSS-ECU (Refer
to GROUP 42B, Troubleshooting ).
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Check of short to power supply, short to earth, and open
circuit
in ACCI line between ignition switch (ACC) <vehicles without
KOS> or ACC relay
connector <vehicles with KOS> and ETACS-ECU
connector
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Repair the connector(s) or wiring
harness. Then go to Step 5.
|
|
|
|
STEP 5. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set in the
ETACS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to
"ON" position.
|
|
(3)Check if diagnosis code is set.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the ETACS-ECU (Refer to GROUP
54A - ETACS, ETACS-ECU ).
|
|
|
|
If the
trouble symptom is resolved, an intermittent malfunction such as poorly
engaged connector(s) or wiring harness is suspected. (Refer to GROUP 00
- How to Use
Troubleshooting/Inspection Service Points - How to Cope with
Intermittent
Malfunction .)
|
|
|