Diagnosis Item
1: Communication with no ECUs is possible (MAIN).
caution |
When servicing a CAN bus line,
earth yourself by touching a metal object such as an unpainted water pipe. If you fail to do,
a component connected to the CAN bus line may be broken.
|
TROUBLESHOOTING HINTS
- Malfunction in CAN main bus line (short to earth or power
supply, wire short to one another)
- Malfunction in the ECUs which are interconnected via CAN main bus line (internal error)
- Malfunction (open circuit) of wiring harness, connector (s) between the diagnosis
connector and joint connector(s)
|
STEP 1. Check the CAN bus lines for short to power supply.
Voltage measurement at diagnosis connector.
|
|
caution |
A digital multimeter should be used. For details refer to .
|
|
|
caution |
The test wiring harness should be used. For details refer
to .
|
|
|
(1)Connect the negative battery terminal, and turn the ignition switch to the "ON"
position.
|
|
(2)Voltage between diagnosis connector terminal No.6 (CAN_H) and body earth. OK: Less than 4.0 V
|
|
(3)Voltage between diagnosis connector terminal No.14 (CAN_L) and body earth. OK: Less than 4.0 V
|
|
(4)Disconnect the negative battery terminal.
|
|
Q.
Is the check result normal?
|
|
YES <Voltage is less than 4.0 V in both CAN_H and CAN_L> : Go to Step 2.
|
|
|
|
NO <Voltage is 4.0 V or more in either CAN_H or CAN_L> : Perform diagnosis item 2 "Diagnose shorts in the power supply to CAN bus line
(MAIN)" (Refer to ).
|
|
|
|
STEP 2. Check the CAN bus lines for short to earth. Resistance measurement
at diagnosis connector.
|
|
caution |
A digital multimeter should be used. For details refer to .
|
|
|
caution |
The test wiring harness should be used. For details refer
to .
|
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(2)
caution |
When measuring the resistance, disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is disconnected.
|
|
(3)Resistance between diagnosis connector terminal No.6 (CAN_H) and body
earth. OK: 1 kΩ or more
|
|
(4)Resistance between diagnosis connector terminal No.14 (CAN_L) and body
earth. OK: 1 kΩ or more
|
|
Q.
Is the check result normal?
|
|
YES <Resistance value is 1 kΩ or more in both CAN_H and CAN_L> : Go to Step 3.
|
|
|
|
NO <Resistance value is less than 1 kΩ in either CAN_H or
CAN_L> : Perform diagnosis item 3 "Diagnose shorts in the earth to CAN bus line (MAIN)"
(Refer to ).
|
|
|
|
STEP 3. Check the CAN bus lines for short to each other. Resistance
measurement at diagnosis connector.
|
|
caution |
A digital multimeter should be used. For details refer to .
|
|
|
caution |
The test wiring harness should be used. For details refer
to .
|
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(2)
caution |
When measuring the resistance, disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is disconnected.
|
|
(3)Resistance between diagnosis connector terminal Nos.6 and 14. OK: 60 ± 10 Ω
|
|
Q.
Is the check result normal?
|
|
YES : The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to Use Troubleshooting/inspection Service Points - How to Cope with Intermittent
Malfunction ).
|
|
|
|
NO <Resistance value is less than 60 ± 10 Ω> : Perform diagnosis Item 4 "Diagnose shorts between CAN_H and L lines (MAIN)"
(Refer to ).
|
|
|
|
NO <Resistance value is 1 kΩ or more> : Check the wires between diagnosis connector and joint connector (CAN1) for open
circuit, and check the terminal resistors in the engine-ECU and the ETACS-ECU for open circuit.
Then repair or replace if necessary.
|
|
|