Diagnosis Item
20: Diagnose when the M.U.T.-III cannot receive the data sent by FCM-ECU <Vehicles with
forward collision mitigation system>.
caution |
When servicing a CAN bus line,
earth yourself by touching a metal object such as an unpainted water pipe. If you fail to do,
a component connected to the CAN bus line may be broken.
|
FUNCTION
The diagnostic result demonstrates that "the M.U.T.-III cannot receive the sent data from
the FCM-ECU" when the M.U.T.-III checks the periodically sent data from each ECU and cannot
receive the FCM-ECU data only.
TROUBLE JUDGEMENT CONDITIONS
M.U.T.-III judges the trouble when the periodically sent data from FCM-ECU cannot be received.
PROBABLE CAUSES
- Damaged harness wires and connectors
- Power supply circuit malfunction of the FCM-ECU
- Malfunction of the FCM-ECU
|
STEP 1. Connector check: joint connector (CAN1), joint connector
(CAN3), D-26 intermediate connector and FCM-ECU connector
|
|
caution |
The strand end of the twist wire should be within 10 cm from
the connector. For details refer to .
|
|
|
When checking the joint connector, ensure that its wiring harness side and its short pins
are not damaged.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair the defective connector. Replace the joint connector as necessary.
|
|
|
|
STEP 2. Resistance measurement at joint connector (CAN1) and D-26
intermediate connector.
|
|
caution |
A digital multimeter should be used. For details refer to .
|
|
|
caution |
The test wiring harness should be used. For details refer
to .
|
|
|
(1)Disconnect the joint connector (CAN1) and D-26 intermediate connector, and measure
at the wiring harness side.
|
|
(2)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(3)
caution |
When measuring the resistance, disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is disconnected.
|
|
(4)Continuity between joint connector (CAN1) terminal No.11 and D-26 intermediate
connector terminal No.19. OK: Continuity (2 Ω or less)
|
|
(5)Continuity between joint connector (CAN1) terminal No.22 and D-26 intermediate
connector terminal No.18. OK: Continuity (2 Ω or less)
caution |
Strictly observe the specified wiring harness repair procedure.
For details refer to .
|
|
|
Q.
Is the check result normal?
|
|
<All the resistances measure 2 Ω or less> Go to Step 3
.
|
|
|
|
NO : <Either or all of the resistances measure more than 2 Ω> Repair
the wiring harness between joint connector (CAN1) and D-26 intermediate connector.
|
|
|
|
STEP 3. Resistance measurement at D-26 intermediate connector and
joint connector (CAN3).
|
|
caution |
A digital multimeter should be used. For details refer to .
|
|
|
caution |
The test wiring harness should be used. For details refer
to .
|
|
|
(1)Disconnect the D-26 intermediate connector and joint connector (CAN3), and measure
at the wiring harness side.
|
|
(2)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(3)
caution |
When measuring the resistance, disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is disconnected.
|
|
(4)Continuity between D-26 intermediate connector terminal No.19 and joint connector
(CAN3) terminal No.10. OK: Continuity (2 Ω or less)
|
|
(5)Continuity between D-26 intermediate connector terminal No.18 and joint connector
(CAN3) terminal No.21. OK: Continuity (2 Ω or less)
caution |
Strictly observe the specified wiring harness repair procedure.
For details refer to .
|
|
|
Q.
Is the check result normal?
|
|
<All the resistances measure 2 Ω or less> Go to Step 4
.
|
|
|
|
NO : <Either or all of the resistances measure more than 2 Ω> Repair
the wiring harness between D-26 intermediate connector and joint connector (CAN3).
|
|
|
|
STEP 4. Resistance measurement at joint connector (CAN3) and FCM-ECU
connector.
|
|
caution |
A digital multimeter should be used. For details refer to .
|
|
|
caution |
The test wiring harness should be used. For details refer
to .
|
|
|
(1)Disconnect joint connector (CAN3) and the FCM-ECU connector, and measure at the
wiring harness side.
|
|
(2)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(3)
caution |
When measuring the resistance, disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is disconnected.
|
|
(4)Continuity between joint connector (CAN3) terminal No.9 and FCM-ECU connector terminal
No.7 OK: Continuity (2 Ω or less)
|
|
(5)Continuity between joint connector (CAN3) terminal No.20 and FCM-ECU connector
terminal No.6 OK: Continuity (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
<All the resistances measure 2 Ω or less> Power supply
to the FCM-ECU may be suspected (Refer to GROUP 35C - Troubleshooting ).
|
|
|
|
NO : <Either or all of the resistances measure more than 2 Ω> Repair
the wiring harness between joint connector (CAN3) and the FCM-ECU connector.
|
|
|