Diagnosis Item 21: Diagnose when the M.U.T.-III cannot receive the data sent by engine-ECU. <Vehicles for RHD>
caution |
When servicing a CAN bus line, earth yourself by touching a metal object such as an unpainted water pipe. If you fail to do, a component connected to the CAN bus line may be broken.
|
FUNCTION
The diagnostic result demonstrates that "the M.U.T.-III cannot receive the sent data from the engine-ECU" when the M.U.T.-III checks the periodically sent data from each ECU and cannot receive the engine-ECU data only.
TROUBLE JUDGEMENT CONDITIONS
M.U.T.-III judges the trouble when the periodically sent data from engine-ECU cannot be received.
PROBABLE CAUSES
- Damaged harness wires and connectors
- Power supply circuit malfunction of the engine-ECU
- Malfunction of the engine-ECU
|
STEP 1. Connector check: joint connector (CAN1), joint connector (CAN3), D-26 intermediate connector and engine-ECU connector
|
|
caution |
The strand end of the twist wire should be within 10 cm from the connector.
|
|
|
When checking the joint connector, ensure that its wiring harness side and its short pins are not damaged.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair the defective connector. Replace the joint connector as necessary.
|
|
|
|
STEP 2. Resistance measurement at joint connector (CAN1) and D-26 intermediate connector.
|
|
caution |
A digital multimeter should be used.
|
|
|
caution |
The test wiring harness should be used.
|
|
|
(1)Disconnect the joint connector (CAN1) and D-26 intermediate connector, and measure at the wiring harness side.
|
|
(2)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(3)
caution |
When measuring the resistance, disconnect the negative battery terminal.
|
Ensure that the negative battery terminal is disconnected.
|
|
(4)Continuity between joint connector (CAN1) terminal No.11 and D-26 intermediate connector terminal No.19. OK: Continuity (2 Ω or less)
|
|
(5)Continuity between joint connector (CAN1) terminal No.22 and D-26 intermediate connector terminal No.18. OK: Continuity (2 Ω or less)
caution |
Strictly observe the specified wiring harness repair procedure.
|
|
|
Q.
Is the check result normal?
|
|
<All the resistances measure 2 Ω or less> Go to Step 3
.
|
|
|
|
NO : <Either or all of the resistances measure more than 2 Ω> Repair the wiring harness between joint connector (CAN1) and D-26 intermediate connector.
|
|
|
|
STEP 3. Resistance measurement at D-26 intermediate connector and joint connector (CAN3).
|
|
caution |
A digital multimeter should be used.
|
|
|
caution |
The test wiring harness should be used.
|
|
|
(1)Disconnect the D-26 intermediate connector and joint connector (CAN3), and measure at the wiring harness side.
|
|
(2)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(3)
caution |
When measuring the resistance, disconnect the negative battery terminal.
|
Ensure that the negative battery terminal is disconnected.
|
|
(4)Continuity between D-26 intermediate connector terminal No.19 and joint connector (CAN3) terminal No.10. OK: Continuity (2 Ω or less)
|
|
(5)Continuity between D-26 intermediate connector terminal No.18 and joint connector (CAN3) terminal No.21. OK: Continuity (2 Ω or less)
caution |
Strictly observe the specified wiring harness repair procedure.
|
|
|
Q.
Is the check result normal?
|
|
<All the resistances measure 2 Ω or less> Go to Step 4
.
|
|
|
|
NO : <Either or all of the resistances measure more than 2 Ω> Repair the wiring harness between D-26 intermediate connector and joint connector (CAN3).
|
|
|
|
STEP 4. Resistance measurement at joint connector (CAN3) and engine-ECU connector.
|
|
caution |
A digital multimeter should be used.
|
|
|
caution |
The test wiring harness should be used.
|
|
|
(1)Disconnect the joint connector (CAN3) and the engine-ECU connector, and measure at the wiring harness side.
|
|
(2)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(3)
caution |
When measuring the resistance, disconnect the negative battery terminal.
|
Ensure that the negative battery terminal is disconnected.
|
|
(4)Continuity between joint connector (CAN3) terminal No.11 and engine-ECU connector terminal No.101 <6B31>, 108 <4N15, 4D56>. OK: Continuity (2 Ω or less)
|
|
(5)Continuity between joint connector (CAN3) terminal No.22 and engine-ECU connector terminal No.102 <6B31>, 109 <4N15, 4D56>. OK: Continuity (2 Ω or less)
caution |
Strictly observe the specified wiring harness repair procedure.
|
|
|
Q.
Is the check result normal?
|
|
<All the resistances measure 2 Ω or less> Go to Step 5
.
|
|
|
|
NO : <Either or all of the resistances measure more than 2 Ω> Repair the wiring harness between joint connector (CAN3) and the engine-ECU.
|
|
|
|
STEP 5. Resistance measurement at engine-ECU connector.
|
|
caution |
A digital multimeter should be used.
|
|
|
(1)Remove the engine-ECU, and measure at the equipment side.
|
|
(2)Resistance between engine-ECU connector terminal Nos.101 and 102 <6B31> or 108 and 109 <4N15, 4D56>. OK: 120 ± 20 Ω
caution |
Strictly observe the specified wiring harness repair procedure.
|
|
|
Q.
Is the check result normal?
|
|
<Within 120 ± 20 Ω> Power supply to the engine-ECU may be suspected. Diagnose the fuel system (Refer to GROUP 13B - Troubleshooting <6B31>, GROUP 13C - Troubleshooting <4N15> or GROUP 13E - Troubleshooting <4D56>).
|
|
|
|
<Not within 120 ± 20 Ω> Replace the engine-ECU (Refer to GROUP 13B - Engine-ECU <6B31>, GROUP 13C - Engine-ECU <4N15> or GROUP 13E - Engine-ECU <4D56>).
|
|
|