Inspection Procedure
4: Cruise Control cannot be Set (No Response SET - Switch and RES + Switch is
Pressed).
COMMENTS ON TROUBLE SYMPTOM
The fail-safe function is probably cancelling cruise control system. In this case, checking
the cruise control system, MPI system, ASTC system, CAN bus system and A/T system diagnosis
codes. The M.U.T.-III can also be used to check if the circuits of each input switch are normal
or not by checking the data list.
note |
Press the cruise control switches one by one securely. Otherwise, the cruise control system
may not be started.
|
PROBABLE CAUSES
- Malfunction of CAN bus system.
- Malfunction of the MPI system.
- Malfunction of the ASTC system.
- Malfunction of the cruise control switches.
- Malfunction of the stop lamp switch.
- Malfunction of the clutch switch.
- Malfunction of the engine-ECU.
|
caution |
- If there is any problem in the CAN bus lines,
an incorrect diagnosis code may be set. Prior to this diagnosis, diagnose the CAN bus lines.
- Before replacing the ECU, ensure that the CAN bus lines is normal.
|
|
|
STEP 1. Check the CAN bus system diagnosis.
|
|
Using M.U.T.-III, perform CAN bus diagnosis (Refer to GROUP 54C - Explanation
About The M.U.T.-III Can Bus Diagnostics).
|
|
Q.
Is the check result satisfactory?
|
|
Go to Step 2.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - Troubleshooting, Can Bus
Diagnostic Table). Then go to Step 9.
|
|
|
|
STEP 2. Check the MPI system diagnosis code.
|
|
Using M.U.T.-III, perform MPI system diagnosis code (Refer to GROUP 13A - Troubleshooting,
Diagnosis Function).
|
|
Q.
Is any diagnosis code set?
|
|
Repair the MPI system (Refer to GROUP 13A - Troubleshooting, Inspection
Chart for Diagnosis Code ). Then go to Step 9.
|
|
|
|
Go to Step 3
|
|
|
|
STEP 3. Check the ASTC system diagnosis code.
|
|
Using M.U.T.-III, perform ASTC system diagnosis code.
|
|
Q.
Is any diagnosis code set?
|
|
Repair the ASTC system (Refer to GROUP 35C - Troubleshooting, Diagnosis
Code Chart). Then go to Step 9.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Check the diagnosis code.
|
|
(1)Use the M.U.T.-III, erase the diagnosis code of the cruise control system.
|
|
(2)Turn the ignition switch to the "ON" position, and press the cruise control ON/OFF
switch to turn the cruise control system to ON (turn ON the cruise control indicator lamp).
|
|
(3)After turning the cruise control system to ON, when 2 minutes or more has elapsed
without operating the cruise control switches.
|
|
(4)With the cruise control switches not operated, depress the brake pedal for several
seconds, and then read the diagnosis code of the cruise control system.
|
|
Q.
Is any diagnosis code set?
|
|
Repair the cruise control system. Then go to Step 9.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. Check the data list.
|
|
Using M.U.T.-III, check the data list (Refer to data list reference table ).
|
|
- Item 75: CANCEL switch
- Item 86: Cruise control ON/OFF switch
- Item 91: RES + switch
- Item 92: SET - switch
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Refer to - Diagnosis Code Procedures,
Code No.P1564: Cruise control switch system. Then go to Step 9.
|
|
|
|
STEP 6. Check the data list.
|
|
Using M.U.T.-III, check the data list.
|
|
- Item 74: Stop lamp switch
- Item 89: Brake switch
|
|
Q.
Is the check result normal?
|
|
Go to Step 7
|
|
|
|
Refer to - Diagnosis Code Procedures,
Code No.P1571: Stop lamp switch system. Then go to Step 9.
|
|
|
|
STEP 7. Check the data list.
|
|
Using M.U.T.-III, check the data list (Refer to data list reference table ).
|
|
Q.
Is the check result normal?
|
|
Go to Step 8.
|
|
|
|
Refer to - Symptom Procedures, Inspection
Procedure 2. Then go to Step 9.
|
|
|
|
STEP 8. Check the symptom.
|
|
Q.
Can cruise control be set?
|
|
It can be assumed that this malfunction is intermittent (Refer to GROUP 00 - How
to Use Troubleshooting/Inspection Service Points, How to Cope with Intermittent Malfunction).
|
|
|
|
Replace the engine-ECU (Refer to GROUP 13A - Engine-ECU). Then go to
Step 9.
|
|
|
|
STEP 9. Check the symptom.
|
|
Q.
Can cruise control be set?
|
|
The procedure is complete.
|
|
|
|
Return to Step 1.
|
|
|