Code No.P0882: Power supply system
PROBABLE CAUSES
OPERATION
The A/T-ECU is energised via the A/T control relay from the battery.
DIAGNOSIS CODE SET CONDITION
While the engine is running, if a status continues for 20 seconds with which the power supply voltage to A/T-ECU is 9 V or less (1 drive cycle), code No.P0882 is set.
PROBABLE CAUSES
- Malfunction of A/T control relay
- Damaged harness wires and connectors
- Malfunction of the A/T-ECU
|
STEP 1. Check the A/T control relay
|
|
Refer to .
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Replace the A/T control relay.
|
|
|
|
STEP 2. Measure the voltage at A/T control relay connector.
|
|
Disconnect the connector, and measure the voltage between terminal No.4 and earth at the harness side.
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 3.
|
|
|
|
STEP 3. Check for open circuit, short circuit and harness damage in relay switch side power supply line between A/T control relay connector and battery.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the connector(s) or the wiring harness.
|
|
|
|
STEP 4. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set.
|
|
Q.
Is diagnosis code No.P0882 set?
|
|
Replace the A/T-ECU.
|
|
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
STEP 5. Measure the voltage at the A/T control relay connector.
|
|
(1)Disconnect the connector, and measure the voltage between terminal No.1 and earth at the harness side.
|
|
(2)Turn the ignition switch to the ON position. OK: System voltage
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
Go to Step 6.
|
|
|
|
STEP 6. Check for open circuit, short circuit and harness damage in relay coil side power supply line between A/T control relay connector and J/B connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the connector(s) or the wiring harness.
|
|
|
|
STEP 7. Measure the resistance at A/T control relay connector.
|
|
Disconnect the connector, and measure the resistance between terminal No.2 and earth at the harness side.
|
|
Q.
Is the check result normal?
|
|
Go to Step 9.
|
|
|
|
Go to Step 8.
|
|
|
|
STEP 8. Check for open circuit and harness damage in relay coil side earth line between A/T control relay connector and earth.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the connector(s) or the wiring harness.
|
|
|
|
STEP 9. Measure the resistance at A/T-ECU connector.
|
|
Disconnect the connector, and measure the resistance between terminal GRP1, GRP2 line and earth at the harness side.
|
|
Q.
Is the check result normal?
|
|
Go to Step 11.
|
|
|
|
Go to Step 10.
|
|
|
|
STEP 10. Check for open circuit and harness damage in GRP1, GRP2 line between A/T-ECU connector and earth.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the connector(s) or the wiring harness.
|
|
|
|
STEP 11. Measure the voltage at the A/T-ECU connector.
|
|
(1)Measure the voltage between terminal No.1 and earth at the ECU side.
|
|
(2)Turn the ignition switch to the ON position. OK: System voltage
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Go to Step 12.
|
|
|
|
STEP 12. Check for open circuit, short circuit and harness damage in between A/T control relay connector and A/T-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the connector(s) or the wiring harness.
|
|
|