Code No. C1860:
High voltage at ASTC-ECU power supply
caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table
).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
- When the hydraulic unit (integrated with ASTC-ECU) is replaced, always carry out
the calibration of the steering wheel sensor and the G and yaw rate sensor (Refer to
).
|
OPERATION
The ASTC-ECU is energised by the ignition switch through the multi-purpose fuse at the
terminal IG1.
DIAGNOSIS CODE SET CONDITION
This diagnosis code is set when the power supply voltage of the ASTC-ECU is abnormally
high.
PROBABLE CAUSES
- Overcurrent
- Battery abnormality
- Charging system failed
- Malfunction of the hydraulic unit assembly (integrated with ASTC-ECU)
|
STEP 1. M.U.T.-III CAN bus diagnosis
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnosis Table ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Erase the diagnosis code.
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code No. C1860 set?
|
|
Go to Step 3.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunctions ).
|
|
|
|
STEP 3. Check the battery
|
|
Refer to GROUP 54A - Battery Test .
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Charge or replace the battery (Refer to GROUP 54A - Battery ).
Then go to Step 6.
|
|
|
|
STEP 4. Check the charging system
|
|
Refer to GROUP 16 - Charging System .
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Repair or replace the charging system component(s) (Refer to GROUP 16 - Alternator ).
Then go to Step 6.
|
|
|
|
STEP 5. Check whether the diagnosis code is set again.
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Erase the diagnosis code.
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code No. C1860 set?
|
|
Replace the hydraulic unit assembly (integrated with ASTC-ECU) (Refer to ).
Then go to Step 6.
|
|
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to Cope with Intermittent Malfunction ).
|
|
|
|
STEP 6. Check whether the diagnosis code is set again.
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Erase the diagnosis code.
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code No. C1860 set?
|
|
Return to Step 1.
|
|
|
|
The procedure is complete.
|
|
|