Code No. C1295:
Transfer position error
| caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table
 ).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
- When the hydraulic unit (integrated with ASTC-ECU) is replaced, always carry out
the calibration of the steering wheel sensor and the G and yaw rate sensor (Refer to ).
|
OPERATION
The transfer position switch output signal is sent to ASTC-ECU via the CAN bus lines from
transfer-ECU.
DIAGNOSIS CODE SET CONDITION
This diagnosis code will be set when the transfer-ECU detects a fault in the transfer
system.
PROBABLE CAUSES
Current trouble
- The CAN bus line is defective.
- Malfunction of transfer
- Malfunction of transfer position switch
- Malfunction of the transfer-ECU
- Malfunction of the hydraulic unit assembly (integrated with ASTC-ECU)
Past trouble
- Carry out diagnosis with particular emphasis on the back-up lamp
switch, connector(s) or wiring harness between the back-up lamp switch to the junction block
or ETACS-ECU. For diagnosis procedures, refer to How to treat past trouble (GROUP 00 - How
to Use Troubleshooting/Inspection Service Points ).
|
|
STEP 1. M.U.T.-III CAN bus diagnosis
|
|
|
Use M.U.T.-III to diagnose the CAN bus lines.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 3.
|
|
|
|
|
|
 Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnosis Table ).
On completion, go to Step 2.
|
|
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
|
Check again if the diagnosis code is set.
|
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
|
(3)Erase the diagnosis code.
|
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
|
(6)Check if the diagnosis code is set.
|
|
|
Q.
Is diagnosis code No. C1295 set?
|
|
|
Go to Step 3.
|
|
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunctions ).
|
|
|
|
|
|
STEP 3. Use M.U.T.-III to confirm a diagnosis code of other systems.
|
|
|
Check if the diagnosis code is set in the transfer-ECU (Refer to GROUP 22A - Diagnosis
Code Chart <M/T> or GROUP 23A - Diagnosis
Code Chart <A/T-ES4>, <A/T-SS4)>).
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Troubleshoot the transfer-ECU diagnosis code. Then go to Step 5.
|
|
|
|
|
|
Go to Step 4.
|
|
|
|
|
|
STEP 4. Check whether the diagnosis code is set again.
|
|
|
Check again if the diagnosis code is set.
|
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
|
(3)Erase the diagnosis code.
|
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
|
(6)Check if the diagnosis code is set.
|
|
|
Replace the hydraulic unit assembly (integrated with ASTC-ECU) (Refer to ).
Then go to Step 5.
|
|
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunctions ).
|
|
|
|
|
|
STEP 5. Check whether the diagnosis code is set again.
|
|
|
Check again if the diagnosis code is set.
|
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
|
(3)Erase the diagnosis code.
|
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
|
(6)Check if the diagnosis code is set.
|
|
|
Q.
Is diagnosis code No. C1295 set?
|
|
|
Return to Step 1.
|
|
|
|
|
|
The procedure is complete.
|
|
|
|