Code No. U1211:
ENG Parity/Toggle Bit Error
caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table
).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
- When the hydraulic unit (integrated with ASTC-ECU) is replaced, always carry out
the calibration of the steering wheel sensor and the G and yaw rate sensor.
|
OPERATION
Engine-related signals are sent or received to and from between ASTC-ECU and engine-ECU
via CAN bus lines.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is set when the engine-ECU has detected an abnormal engine-related signal.
PROBABLE CAUSES
- The CAN bus line is defective.
- Malfunction of the engine-ECU
- Malfunction of the hydraulic unit assembly (integrated with ASTC-ECU)
|
STEP 1. M.U.T.-III CAN bus diagnosis
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
Q.
Is diagnosis code No. U1211 set?
|
|
Go to Step 3.
|
|
|
|
This diagnosis is complete.
|
|
|
|
STEP 3. Use M.U.T.-III to confirm a diagnosis code of other systems.
|
|
Check if the diagnosis code is set in the engine-ECU (Refer to GROUP 13A - Diagnosis
Code Chart) <4G64> or (Refer to GROUP 13B - Diagnosis Code Chart) <4D56>.
|
|
Q.
Is the diagnosis code set?
|
|
Erase the diagnosis code. Then go to Step 6.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set.
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Erase the diagnosis code.
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code No. U1211 set?
|
|
Replace the engine-ECU (Refer to GROUP 13A - Engine-ECU) <4G64> or
(Refer to GROUP 13B - Engine-ECU) <4D56>. Then go to Step 5.
|
|
|
|
This diagnosis is complete.
|
|
|
|
STEP 5. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set.
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Erase the diagnosis code.
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code No. U1211 set?
|
|
Replace the hydraulic unit assembly (integrated with ASTC-ECU). Then go to Step
6.
|
|
|
|
This diagnosis is complete.
|
|
|
|
STEP 6. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set.
|
|
(1)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Erase the diagnosis code.
|
|
(4)Turn the ignition switch to the "LOCK" (OFF) position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code No. U1211 set?
|
|
Return to Step 1.
|
|
|
|
The procedure is complete.
|
|
|