Code No. B1452 Left curtain air bag module (squib) system (shorted to
squib circuit earth)
caution |
If diagnosis code No. B1452 is set in the SRS-ECU, be
sure to diagnose the CAN bus line.
|
OPERATION
In case of side collision, when the impact exceeding the
threshold is applied to the vehicle, and when the impact is simultaneously
detected (turned ON) by the side impact sensor as well as by the analogue
G-sensor in SRS-ECU, the electric current is supplied from SRS-ECU to the
curtain air bag module (squib) of impacted side.
TROUBLE JUDGEMENT
The code is set when the input terminal of
SRS-ECU curtain air bag module (squib) is shorted to earth.
PROBABLE CAUSES
- Damaged wiring harness and connector
- Curtain air bag module (squib) harness shorted to earth
- Malfunction of SRS-ECU
|
STEP 1. M.U.T.-III CAN bus diagnostics.
|
|
Use M.U.T.-III to diagnose the CAN bus
lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair
the CAN bus line (Refer to GROUP 54C - Troubleshooting ).
|
|
|
|
STEP 2. Check whether the diagnosis code is set again.
|
|
(1)Connect the negative battery terminal.
|
|
(2)After erasing the diagnosis code memory, check the
diagnosis code again.
|
|
(3)Disconnect the negative battery terminal.
|
|
Q.
Is diagnosis code No. B1452 set?
|
|
Go to Step 3.
|
|
|
|
Intermittent malfunction (Refer to
GROUP 00 - How to Use Troubleshooting/Inspection Service Points
- How to Cope with Intermittent Malfunction ).
|
|
|
|
STEP 3. Diagnosis check by dummy resistor connection
|
|
(1)Check that the negative battery terminal is disconnected.
If connected, disconnect the negative battery terminal.
|
![](../../../img/52/AC904706AC00ENG.png)
|
(2)Use the flat-tipped screwdriver to pull out
the locking button of left curtain air bag module connector to the
direction of the arrow. After releasing the lock, disconnect the connector.
|
![](../../../img/52/AC301553DQ00ENG.png)
|
(3)Connect the dummy resistor (Special tool:
MB991865) to the resistor harness (Special tool: MB991884). (4)Connect
the resistor harness (special tool) to left curtain air bag module
connector. (5)Connect the negative battery terminal. (6)After erasing
the diagnosis code memory, check the diagnosis code again. (7)Disconnect
the negative battery terminal.
Q.
Is diagnosis code No. B1452 set?
Go to Step 4.
Replace the left curtain air bag
module (Refer to .)
|
|
STEP 4. Resistance measurement at the SRS-ECU connector.
|
|
(1)Check that the negative battery terminal is disconnected.
If the negative battery terminal is connected, disconnect it.
|
|
(2)Disconnect the SRS-ECU connector.
|
![](../../../img/52/AC904706AC00ENG.png)
|
(3)
danger |
To release SRS-ECU wiring harness side connector
short spring in the following operations, disconnect curtain air bag
module connector in advance, and keep the squib circuit
shorted.
|
Use the flat-tipped screwdriver to pull out the locking button of
left curtain air bag module connector to the direction of the arrow. After
releasing the lock, disconnect the connector.
|
![](../../../img/52/ACE02056AB00ENG.png)
|
(4)
caution |
The short spring may not be released due to the
insufficient insertion. Therefore, insert the insulator for 4 mm or
more.
|
Insert an insulator (width: 3 mm, thickness: 0.5 mm) such as cable
tie between the CLS+, CLS- line and the short spring, and release the
short spring. (5)Check the continuity between the SRS-ECU harness side
connector CLS+, CLS- line and the body earth. OK: No
continuity
Q.
Is the check result normal?
Go to Step 5.
Repair the wiring
harness.
|
|
STEP 5. Check whether the diagnosis code is set again.
|
|
Q.
Is diagnosis code No. B1452 set?
|
|
Replace SRS-ECU (Refer to ).
|
|
|
|
Intermittent Malfunction (Refer to
GROUP 00 - How to Use Troubleshooting/Inspection Service Points
- How to Cope with Intermittent Malfunction ).
|
|
|