Code No. B1619
Driver’s lap pre-tensioner (squib) system (short circuit
between squib circuit terminals)
caution |
If diagnosis code B1619 is
stored in the SRS-ECU, be sure to diagnose the CAN bus
line.
|
OPERATION
Only when the frontal collision impact that
exceeds the threshold is simultaneously detected
(turned ON) by the front impact sensor as well as by the analogue
G-sensor in SRS-ECU, the electric
current is supplied from SRS-ECU to the lap pre-tensioner (squib).
TROUBLE JUDGEMENT
The code is stored when the short circuit
occurs to between the terminals of SRS-ECU lap
pre-tensioner (squib) circuit.
PROBABLE CAUSES
- Damaged short spring *
- Short circuit between terminals of lap pre-tensioner (squib)
circuit
- Damaged connector(s)
- Malfunction of SRS-ECU
- Insufficient press of locking button or locking button not
pressed
note |
*: The squib circuit connectors
integrate a short spring (which prevents the
lap pre-tensioner from being unintentionally deployed
because of static electricity by shorting
the positive wire to the earth wire in the squib circuit
when the connectors are disconnected).
Therefore, when the above codes are stored, the short spring
may not be released due to the
damaged connector even when the connectors are
connected.
|
|
STEP 1. M.U.T.-III CAN bus diagnostics.
|
|
Use M.U.T.-III to diagnose the CAN
bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step
2.
|
|
|
|
Repair the CAN bus
line (Refer to GROUP 54C - Troubleshooting ).
|
|
|
|
STEP 2. Check whether the diagnosis code is stored
again.
|
|
(1)Connect the negative battery terminal.
|
|
(2)After erasing the diagnosis code memory, check
the diagnosis code again.
|
|
(3)Disconnect the negative battery
terminal.
|
|
Q.
Is diagnosis code No. B1619 stored?
|
|
Go to Step
3.
|
|
|
|
Intermittent
malfunction (Refer to GROUP 00 - How to Use
Troubleshooting/Inspection
Service Points - How to Cope with Intermittent
Malfunction ).
|
|
|
|
STEP 3. Connector check: SRS-ECU, lap
pre-tensioner.
|
|
(1)Check that the negative battery terminal is
disconnected. If the negative battery
terminal is connected, disconnect it.
|
|
(2)After disconnecting the SRS-ECU connector,
connect it again.
|
![](../../../img/52/ACE02073AB00ENG.png)
|
(3)After disconnecting the lap
pre-tensioner harness side connector, connect the connector
again. For the lap pre-tensioner harness side connector
disconnection, use the flat-tipped screwdriver
to pull out the harness side connector locking button. After
releasing the lock, disconnect
the harness side connector. (4)Connect the negative
battery terminal. (5)After erasing the diagnosis code
memory, check the diagnosis code again. (6)Disconnect the
negative battery terminal.
Q.
Is diagnosis code No. B1619 stored?
Go to Step
4.
Replace
the connector concerned.
|
|
STEP 4. Diagnosis check by dummy resistor
connection.
|
|
(1)Check that the negative battery terminal is
disconnected. If the negative battery
terminal is connected, disconnect it.
|
![](../../../img/52/ACE02073AB00ENG.png)
|
(2)Use the flat-tipped screwdriver
to pull out the locking button of harness side connector.
After releasing the lock, disconnect the lap pre-tensioner
harness side connector.
|
![](../../../img/52/ACE02168AB00ENG.png)
|
(3)Connect special tool dummy
resistor (MB991865) to special tool resistor harness
(MB991866). (4)Connect resistor harness to the lap
pre-tensioner harness side connector. (5)Connect the
negative battery terminal. (6)After erasing the diagnosis
code memory, check the diagnosis code
again. (7)Disconnect the negative battery
terminal.
Q.
Is diagnosis code No. B1619 stored?
Go to Step
5.
Replace
the seat belt with pre-tensioner (Refer to ).
|
|
STEP 5. Resistance measurement at the SRS-ECU
connector.
|
|
(1)Check that the negative battery terminal is
disconnected. If the negative battery
terminal is connected, disconnect it.
|
|
(2)Disconnect the SRS-ECU connector.
|
![](../../../img/52/ACE02073AB00ENG.png)
|
(3)
danger |
To release the SRS-ECU
connector short spring in the following
operations, disconnect this lap pre-tensioner
connector, and keep the squib circuit
shorted.
|
Use the flat-tipped screwdriver to pull out the
locking button of harness side connector.
After releasing the lock, disconnect the lap pre-tensioner
harness side connector.
|
![](../../../img/52/ACE02056AB00ENG.png)
|
(4)
caution |
The short spring may not be
released due to the insufficient insertion.
Therefore, insert
the insulator for 4 mm or more.
|
Insert an insulator (width: 3 mm, thickness: 0.5 mm)
such as cable tie between the PA2+,
PA2- line and the short spring and release the short
spring. (5)Take the measurements below at the SRS-ECU
harness side connector.
- Continuity between PA2+, PA2- line
OK: No continuity
Q.
Is the check result normal?
Go to Step
6.
Repair
the wiring harness PA2+, PA2- line between the SRS-ECU
connector
and the lap pre-tensioner connector.
|
|
STEP 6. Check whether the diagnosis code is stored
again.
|
|
Q.
Is diagnosis code No. B1619 stored?
|
|
Replace SRS-ECU
(Refer to ).
|
|
|
|
Intermittent
malfunction (Refer to GROUP 00 - How to Use
Troubleshooting/Inspection
Service Points - How to Cope with Intermittent
Malfunction ).
|
|
|