INSPECTION PROCEDURE 4: The blower air volume cannot be changed
|
COMMENTS ON TROUBLE SYMPTOM
|
|
If air volume cannot be adjusted by using the blower control, the heater controller assembly (A/C-ECU) or the power transistor may be faulty.
|
|
- Malfunction of the power transistor
- Damaged wiring harness or connectors
- Malfunction of the heater controller assembly (A/C-ECU)
|
|
STEP 1. M.U.T.-III CAN bus diagnostics.
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - Troubleshooting ).
|
|
|
|
STEP 2. M.U.T.-III diagnosis code.
|
|
Check that the diagnosis code related to the air conditioner is not set.
|
|
Q.
Is the diagnosis code set?
|
|
Carry out the diagnosis code procedures (Refer to ).
|
|
|
|
Go to Step 3.
|
|
|
|
STEP 3. Check the data list below on the M.U.T.-III.
|
|
All the following items in the data list should be normal.
|
|
Item No.69: Front blower fan (Target)
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Voltage measurement at power transistor connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Voltage between terminal 2 and body earth. OK: System voltage
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. Check open circuit in blower motor line between blower motor and power transistor.
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
Repair or replace the connector(s) or wiring harness.
|
|
|
|
STEP 6. Resistance measurement at the power transistor connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Continuity between terminal 1 and body earth OK: Continuity exists (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
Go to Step 8.
|
|
|
|
STEP 7. Check open circuit power transistor earth line between power transistor connector and body earth.
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
Repair or replace the connector(s) or wiring harness.
|
|
|
|
STEP 8. Voltage measurement at heater controller (A/C-ECU) connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Voltage between BASE terminal and body earth. OK: System voltage
|
|
Q.
Is the check result normal?
|
|
Go to Step 10.
|
|
|
|
Go to Step 9.
|
|
|
|
STEP 9. Check open circuit power transistor and blower motor line between power transistor connector and heater controller (A/C-ECU) connector BASE terminal.
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
Repair or replace the connector(s) or wiring harness.
|
|
|
|
STEP 10. Replace the power transistor (Refer to ) and recheck the trouble symptom.
|
|
Check that the blower motor operates normally.
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
Replace the heater controller assembly (A/C-ECU) (Refer to ).
|
|
|