Code No. P0130: Cylinder 1, 4 Oxygen Sensor System

OPERATION

The sensor signal is inputted to the engine-ECU <M/T> or engine-A/T-ECU <A/T> (terminal No. 109) from the cylinder 1, 4 oxygen sensor output terminal (terminal No. 4).
The cylinder 1, 4 oxygen sensor (terminal No. 2) is earthed with engine-ECU <M/T> or engine-A/T-ECU <A/T> (terminal No. 96).

FUNCTION

The cylinder 1, 4 oxygen sensor converts the concentration of oxygen in the exhaust emission into a voltage and inputs the signal to the engine-ECU <M/T> or engine-A/T-ECU <A/T>.
When the air-fuel ratio is richer than the theoretical air-fuel ratio, the cylinder 1, 4 oxygen sensor outputs a voltage of about 1 V. When it is leaner than the theoretical air-fuel ratio, it outputs a voltage of about 0 V.
In response to the signal, the engine-ECU <M/T> or engine-A/T-ECU <A/T> controls the fuel infection amount so that the air-fuel ratio can be equivalent to the theoretical air-fuel ratio.

TROUBLE JUDGMENT

Check Conditions

Above 3 minutes later after the engine has started up.
The engine coolant temperature is approximately 80°C or higher.
The engine speed is 1200 r/min. or more.
Volumetric efficiency 25% or more.
During the run at the constant speed on the flat road.

Judgment Criterion

When a power voltage of 5 V is applied to the cylinder 1, 4 oxygen sensor in the engine-ECU <M/T> or engine-A/T-ECU <A/T>, the sensor output voltage is 4.5V or more.

PROBABLE CAUSE

Failed cylinder 1, 4 oxygen sensor
Open/short circuit in cylinder 1, 4 oxygen sensor circuit or loose connector contact
Failed engine-ECU <M/T>
Failed engine-A/T-ECU <A/T>

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III data list

Refer to Data List Reference Table .

Item 11: Cylinder 1, 4 oxygen sensor

Q. Is the check result normal?

	Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points ).

	Go to Step 2 .

STEP 2. Connector check: B-26 cylinder 1, 4 oxygen sensor connector

Q. Is the check result normal?

Go to Step 3 .

Repair or replace.

STEP 3. Perform resistance measurement at B-26 cylinder 1, 4 oxygen sensor connector.

Disconnect connector, and measure at harness side.
Resistance between terminal No. 2 and earth.

OK: 2 Ω or less

Q. Is the check result normal?

Go to Step 7 .

Go to Step 4 .

STEP 4. Connector check: C-113 engine-ECU <M/T> connector or engine-A/T-ECU <A/T> connector

Q. Is the check result normal?

Go to Step 5 .

Repair or replace.

STEP 5. Check harness between B-26 (terminal No. 2) cylinder 1, 4 oxygen sensor (front) connector and C-113 (terminal No. 96) engine-ECU <M/T> connector or engine-A/T-ECU <A/T> connector.

note

Before checking harness, check intermediate connector C-115, and repair if necessary.

Check earthing line for open circuit and damage.

Q. Is the check result normal?

Go to Step 6 .

Repair.

STEP 6. M.U.T.-III data list

Refer to Data List Reference Table .

Item 11: Cylinder 1, 4 oxygen sensor

Q. Is the check result normal?

	Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points ).

	Replace engine-ECU <M/T> or engine-A/T-ECU <A/T>.

STEP 7. Perform voltage measurement at B-26 cylinder 1, 4 oxygen sensor connector.

Use special tool test harness (MB991316) to connect connector, and measure at pick-up harness.
Engine: After warm-up
Transmission: Neutral <M/T> or P range <A/T>
Voltage between terminal No. 4 and earth

OK:
When the engine is 2,500 r/min., the output voltage should repeat 0.4 V or less to 0.6 - 1.0 V alternately.

Q. Is the check result normal?

Go to Step 10 .

Go to Step 8 .

STEP 8. Check cylinder 1, 4 oxygen sensor itself.

Check cylinder 1, 4 oxygen sensor itself (Refer to ).

Q. Is the check result normal?

	Go to Step 9 .

	Replace cylinder 1, 4 oxygen sensor.

STEP 9. Connector check: C-113 engine-ECU <M/T> connector or engine-A/T-ECU <A/T> connector

Q. Is the check result normal?

Check output line for damage.

Repair or replace.

STEP 10. Perform voltage measurement at C-113 engine-ECU <M/T> connector or engine-A/T-ECU <A/T> connector.

Measure engine-ECU <M/T> or engine-A/T-ECU <A/T> terminal voltage.
Transmission: Neutral <M/T> or P range <A/T>
Engine: After warm-up
Voltage between terminal No. 109 and earth.

OK:
When the engine is 2,500 r/min., the output voltage should repeat 0.4 V or less to 0.6 - 1.0 V alternately.

Q. Is the check result normal?

Go to Step 12 .

Go to Step 11 .

STEP 11. Connector check: C-113 engine-ECU <M/T> connector or engine-A/T-ECU <A/T> connector

Q. Is the check result normal?

Check output line for open circuit.

Repair or replace.

STEP 12. Connector check: C-113 engine-ECU <M/T> connector or engine-A/T-ECU <A/T> connector

Q. Is the check result normal?

Repair or replace.