|
|
1.Turn the ignition switch
to the "ON" position.
|
|
2.Push the cruise control
ON/OFF switch of the cruise control switches, and
check that the cruise control indicator lamp within the
combination meter illuminates <standard meter>
or the cruise control display screen is displayed on the
multi information display in the combination meter
<high contrast meter>.
3.Push the
cruise control ON/OFF switch again, and check that the
cruise control indicator lamp within the combination meter
<standard meter> or the cruise control display
screen goes out <high contrast meter>.
|
|
|
1.Turn the ignition switch
to the "ON" position.
|
|
|
2.Push the cruise control
ON/OFF switch (cruise control system: ON, cruise
control indicator lamp: illuminated <standard
meter>, cruise control display screen: display
<high contrast meter>).
|
|
|
3.Drive at the desired speed
within the range of approximately 40 km/h or
more.
|
|
4.Push the SET -
switch.
5.Check to be sure that when the SET
- switch is released the speed is the desired constant
speed. The speed limiter will store a set vehicle speed, and
then regulate the vehicle speed within that stored
speed.
| note |
If the vehicle speed decreases
to approximately 15 km/h below the set
speed because of climbing a hill for example, it
is normal for the cruise control to be
cancelled. When the vehicle speed is decelerated
to the low speed limit (approximately 40
km/h) or less, the constant speed driving
will be cancelled even if the vehicle speed is
not decelerated 15 km/h or more from the
set speed.
|
| note |
On the high contrast meter,
when SET - switch is pressed, "SET" will
be displayed on the multi information display in
the combination meter.
|
|
|
|
1.Turn the ignition switch
to the "ON" position.
|
|
|
2.Push the cruise control
ON/OFF switch (cruise control system: ON, cruise
control indicator lamp: illuminated <standard
meter>, cruise control display screen: display
<high contrast meter>).
|
|
|
3.Set to the desired speed
within the range of approximately 40 km/h or
more.
|
|
4.Push the RES +
switch.
5.Check to be sure that acceleration
continues while the RES + switch is pushed, and that
the speed at the time it was released becomes the constant
driving speed.
|
|
|
1.Turn the ignition switch
to the "ON" position.
|
|
|
2.Push the cruise control
ON/OFF switch (cruise control system: ON, cruise
control indicator lamp: illuminated <standard
meter>, cruise control display screen: display
<high contrast meter>).
|
|
|
3.Set to the desired speed
within the range of approximately 40 km/h or
more.
|
|
|
5.Check to be sure that
deceleration continues while the SET - switch is
pushed, and that the speed at the time it was released
becomes the constant driving speed.
|
|
|
1.Turn the ignition switch
to the "ON" position.
|
|
|
2.Push the cruise control
ON/OFF switch (cruise control system: ON, cruise
control indicator lamp: illuminated <standard
meter>, cruise control display screen: display
<high contrast meter>).
|
|
|
3.Set to the desired speed
within the range of approximately 40 km/h or
more.
|
|
4.When any of the following
operations are performed while at constant speed during
cruise control, check if normal driving is resumed and
deceleration occurs.
| note |
The accelerator pedal must NOT
be depressed.
|
(1)
The CANCEL switch is pushed.
(2)
The brake pedal is depressed.
5.At a vehicle speed
of the low speed limit (approximately 40 km/h) or
higher, check if when the RES + switch is pushed, the
vehicle speed returns to the speed before cruise control
driving was cancelled, and constant speed driving
occurs.
6.When the cruise control ON/OFF
switch is pushed again (cruise control system: OFF) while
driving at constant speed, check if normal driving is
resumed and deceleration occurs.
| note |
The accelerator pedal must NOT
be depressed.
|
|