|
If the tail/stop lamps, the
position lamps or the licence plate lamps do not
illuminate, the wiring harness connector(s), the bulb or the
fuse may be defective or burned
out.
|
|
- Burned-out bulb
- Damaged harness wires and connectors
|
![](../../../img/54/AC313362AF00ENG.png)
![](../../../img/54/AC313367AE00ENG.png)
![](../../../img/54/AC313355AD00ENG.png)
![](../../../img/54/AC313365AC00ENG.png)
![](../../../img/54/AC313479AC00ENG.png)
|
Q.
Is the check result normal?
Go to Step
2.
Repair
the defective connector.
|
|
Check the bulb of the lamp which
does not illuminate.
|
|
Q.
Is the check result normal?
|
|
Replace the bulb of
the lamp which does not illuminate.
|
|
|
![](../../../img/54/AC313362AF00ENG.png)
![](../../../img/54/AC313367AE00ENG.png)
![](../../../img/54/AC313355AD00ENG.png)
![](../../../img/54/AC313365AC00ENG.png)
![](../../../img/54/AC313479AC00ENG.png)
|
(1)Disconnect the connector, and
measure at the wiring harness side.
|
![](../../../img/54/AC310506DK00ENG.png)
![](../../../img/54/AC310506DL00ENG.png)
![](../../../img/54/AC301541HZ00ENG.png)
|
(2)Check the resistance between the
lamp connector and body earth.
- Resistance between A-39 position lamp (RH) connector
terminal No.1 and body earth
- Resistance between A-17 position lamp (LH) connector
terminal No.1 and body earth
- Resistance between G-08 tail/stop lamp (RH)
connector terminal No.1 and body
earth
- Resistance between G-20 tail/stop lamp (LH)
connector terminal No.1 and
body earth
- Resistance between G-15 licence plate lamp (RH)
connector terminal No.1 and body earth
- Resistance between G-19 licence plate lamp (LH)
connector terminal No.1 and body
earth
OK: 2 Ω or less
Q.
Is the check result normal?
Go to Step
5.
Go to Step
4.
|
![](../../../img/54/AC313362AG00ENG.png)
![](../../../img/54/AC313367AF00ENG.png)
|
Q.
Is the check result normal?
Go to Step
5.
Repair
the defective connector.
|
![](../../../img/54/AC313363AB00ENG.png)
![](../../../img/54/AC313368AB00ENG.png)
![](../../../img/54/AC313355AD00ENG.png)
![](../../../img/54/AC313365AC00ENG.png)
![](../../../img/54/AC313479AD00ENG.png)
|
note |
Prior to the wiring harness
inspection, check intermediate connector G-14
<licence
plate lamp>, G-21 <tail/stop
lamp (LH) >, and repair if
necessary.
|
- Check the earth wires for open circuit.
Q.
Is the check result normal?
Go to Step
6.
Repair
the wiring harness.
|
![](../../../img/54/AC311521AB00ENG.png)
|
Q.
Is the check result normal?
Go to Step
7.
Repair
the defective connector.
|
![](../../../img/54/AC313396AQ00ENG.png)
![](../../../img/54/AC313392AD00ENG.png)
![](../../../img/54/AC313399AR00ENG.png)
|
note |
<LH drive
vehicles> Prior to the wiring harness
inspection, check intermediate
connector C-16 <tail/stop lamp (LH)
and licence plate lamp>, C-125
<tail/stop
lamp and licence plate lamp>, G-14
<licence plate lamp>, G-21
<tail/stop
lamp (LH)>, junction block connector C-203
<tail/stop lamp (LH)> and
C-210 <tail/stop lamp (LH)>,
and repair if necessary.
|
|
![](../../../img/54/AC313407AZ00ENG.png)
![](../../../img/54/AC313404AV00ENG.png)
![](../../../img/54/AC313409AQ00ENG.png)
|
note |
<RH drive
vehicles> Prior to the wiring harness
inspection, check intermediate
connector C-16 <tail/stop lamp (LH)
and licence plate lamp>, C-125
<tail/stop
lamp and licence plate lamp>, G-14
<licence plate lamp>, G-21
<tail/stop
lamp (LH)>, joint connector C-31
<tail/stop lamp (RH)>,
junction block connector C-203
<tail/stop lamp (LH)> and
C-210 <tail/stop
lamp (LH)>, and repair if
necessary.
|
- Check the output lines for open circuit.
Q.
Is the check result normal?
Go to Step
8.
Repair
the wiring harness.
|
|
Check that the tail lamps, the
position lamps and the licence plate lamps illuminate
normally.
|
|
Q.
Is the check result normal?
|
|
The lamps illuminate normally at
both high and low beams. : The trouble can be an
intermittent malfunction (Refer to GROUP 00 - How
to Cope with Intermittent Malfunction ).
|
|
|
|
When the tail/stop lamps do
not illuminate : Replace the tail/stop lamp socket
assembly.
|
|
|
|
When the position lamps do not
illuminate : Replace the position lamp socket.
|
|
|
|
When the licence plate lamps do not
illuminate : Replace the licence plate lamp socket.
|
|
|