Diagnosis code
No.03 Communication error with front-ECU
|
caution |
If diagnosis code No. 03
is set in the ETACS-ECU, diagnose the CAN bus
lines.
|
|
|
The ETACS-ECU communicates with the
front-ECU through the SWS communication line. If there
is any trouble in that communication, diagnosis code No. 03
will be set.
|
|
COMMENTS ON TROUBLE SYMPTOM
|
|
The front-ECU, the ETACS-ECU,
connector(s), or wiring harness between the two may be
defective.
|
|
- Malfunction of the front ECU
- Malfunction of the ETACS-ECU
- Damaged harness wires and connectors
|
|
Step 1. M.U.T.-III CAN bus diagnostics
|
|
Use the M.U.T.-III to diagnose the
CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step
2.
|
|
|
|
Correct the CAN bus
line. (Refer to Group 54F - Diagnosis .)
|
|
|
|
Step 2. M.U.T.-III diagnosis code
|
|
(2)On completion, check that diagnosis code No.03 is
not reset.
|
|
Q.
Is diagnosis code No.03 set?
|
|
Go to Step
3.
|
|
|
|
The trouble can be
an intermittent malfunction (Refer to GROUP 00 - How
to Cope with Intermittent Malfunction ).
|
|
|
|
Step 3. Connector check: A-14X front-ECU
connector
|
![](../../../img/54/AC311521AB00ENG.png)
|
Q.
Is the check result normal?
Go to Step
4.
Repair
the defective connector.
|
|
Step 4. Voltage measurement at the A-14X front-ECU
connector.
|
![](../../../img/54/AC311521AB00ENG.png)
|
(1)Disconnect the connector, and
measure at the relay box side. (2)Ignition switch:
ON
|
![](../../../img/54/AC310507CJ00ENG.png)
|
(3)Voltage between A-14X front-ECU
connector No.7 and body earth OK: System
voltage
Q.
Is the check result normal?
Go to Step
6.
Go to Step
5.
|
|
Step 5. Check the wiring harness between A-14X front-ECU
connector
terminal No.7 to the fusible link (26).
|
![](../../../img/54/AC311521AB00ENG.png)
|
- Check the power supply line for open
circuit.
Q.
Is the check result normal?
The trouble can be
an intermittent malfunction (Refer to GROUP 00 - How
to Cope with Intermittent Malfunction ).
Repair the wiring
harness.
|
|
Step 6. Connector check: A-15X front-ECU
connector
|
![](../../../img/54/AC311521AC00ENG.png)
|
Q.
Is the check result normal?
Go to Step
7.
Repair
the defective connector.
|
|
Step 7. Resistance measurement at the A-15X front-ECU
connector.
|
![](../../../img/54/AC311521AC00ENG.png)
|
(1)Disconnect the connector, and
measure at the relay box side.
|
![](../../../img/54/AC310506BV00ENG.png)
|
(2)Resistance between A-15X
front-ECU connector terminal No.31 and body
earth OK: 2 Ω or less
Q.
Is the check result normal?
Go to Step
10.
Go to Step
8.
|
|
Step 8. Connector check: A-25 earth
connector
|
![](../../../img/54/AC313371AC00ENG.png)
|
Q.
Is the check result normal?
Go to Step
9.
Repair
the defective connector.
|
|
Step 9. Check the wiring harness between A-15X front-ECU
terminal
connector terminal No.31 to A-25 earth connector
terminal No.5.
|
![](../../../img/54/AC311521AC00ENG.png)
![](../../../img/54/AC313371AC00ENG.png)
|
- Check the earth wires for open circuit.
Q.
Is the check result normal?
The trouble can be
an intermittent malfunction (Refer to GROUP 00 - How
to Cope with Intermittent Malfunction ).
Repair the wiring
harness.
|
|
Step 10. Connector check: C-221 ETACS-ECU
connector
|
![](../../../img/54/AC313421AB00ENG.png)
|
Q.
Is the check result normal?
Go to Step
11.
Repair
the defective connector.
|
|
Step 11. Check the wiring harness between A-15X
front-ECU connector
terminal No.22 to C-221 ETACS-ECU connector terminal
No.59.
|
![](../../../img/54/AC313416AD00ENG.png)
![](../../../img/54/AC313414AD00ENG.png)
|
note |
Prior to the wiring harness
inspection, check joint connector C-01 and
intermediate connector
C-125, and repair if necessary.
|
- Check the communication lines for open
circuit.
Q.
Is the check result normal?
Go to Step
12.
Repair
the wiring harness.
|
|
Step 12. Check whether the diagnosis code is
reset.
|
|
Replace the front ECU, and then
check that the diagnosis code is not reset.
|
|
(1)Replace the front ECU.
|
|
(3)On completion, check that diagnosis code No.03 is
not reset.
|
|
Q.
Is diagnosis code No.03 set?
|
|
Replace the
ETACS-ECU.
|
|
|
|
The procedure is
complete.
|
|
|