|
1.Turn the ignition switch
to the "ON" position.
|
![](../../../img/17/ACF00308AB00ENG.png)
![](../../../img/17/ACF00690AB00ENG.png)
|
2.Push the cruise control
ON/OFF switch of the cruise control switches, and
check that the cruise control display screen is displayed on
the multi information display in the combination
meter. 3.Push the cruise control ON/OFF
switch again, and check that the cruise control display
screen goes out.
|
|
1.Turn the ignition switch
to the "ON" position.
|
|
2.Push the cruise control
ON/OFF switch (cruise control system: ON, cruise
control display screen: display).
|
|
3.Drive at the desired speed
within the range of approximately 40 km/h or
more.
|
![](../../../img/17/ACF00308AC00ENG.png)
|
4.Press down the SET -
switch. 5.Check to be sure that when the SET
- switch is released the speed is the desired constant
speed.
note |
If the vehicle speed decreases
to approximately 15 km/h below the set
speed because of climbing a hill for example, it
is normal for the cruise control to be
cancelled. When the vehicle speed is decelerated
to the low speed limit (approximately 40
km/h) or less, the constant speed driving
will be cancelled even if the vehicle speed is
not decelerated 15 km/h or more from the
set speed.
|
note |
When SET - switch is
pressed, "SET" will be displayed on the multi
information display in the combination
meter.
|
|
|
1.Turn the ignition switch
to the "ON" position.
|
|
2.Push the cruise control
ON/OFF switch (cruise control system: ON, cruise
control display screen: display).
|
|
3.Set to the desired speed
within the range of approximately 40 km/h or
more.
|
![](../../../img/17/ACF00308AD00ENG.png)
|
4.Press up the RES +
switch. 5.Check to be sure that acceleration
continues while the RES + switch is pushed, and that
the speed at the time it was released becomes the constant
driving speed.
note |
Acceleration can be continued
even if the vehicle speed has passed the high
speed limit. But the constant driving speed when
the RES + switch is released will be
recorded as the high speed limit.
|
|
|
1.Turn the ignition switch
to the "ON" position.
|
|
2.Push the cruise control
ON/OFF switch (cruise control system: ON, cruise
control display screen: display).
|
|
3.Set to the desired speed
within the range of approximately 40 km/h or
more.
|
|
4.Press down the SET -
switch.
|
|
5.Check to be sure that
deceleration continues while the SET - switch is
pushed, and that the speed at the time it was released
becomes the constant driving speed.
|
|
1.Turn the ignition switch
to the "ON" position.
|
|
2.Push the cruise control
ON/OFF switch (cruise control system: ON, cruise
control display screen: display).
|
|
3.Set to the desired speed
within the range of approximately 40 km/h or
more.
|
![](../../../img/17/ACF00308AE00ENG.png)
|
4.When any of the following
operations are performed while at constant speed during
cruise control, check if normal driving is resumed and
deceleration occurs.
note |
The accelerator pedal must NOT
be depressed.
|
(1)
The CANCEL switch is pushed. (2)
The brake pedal is depressed. 5.At a vehicle speed
of the low speed limit (approximately 40 km/h) or
higher, check if when the RES + switch is pushed, the
vehicle speed returns to the speed before cruise control
driving was cancelled, and constant speed driving
occurs. 6.When the cruise control ON/OFF
switch is pushed again (cruise control system: OFF) while
driving at constant speed, check if normal driving is
resumed and deceleration occurs.
note |
The accelerator pedal must NOT
be depressed.
|
|