![](../../../img/54/AC313417AZ00ENG.png)
![](../../../img/54/AC313414AT00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from
the connector. For details refer to .
|
Q.
Are the check result normal?
Go to Step
2.
Repair
the defective connector.
|
![](../../../img/54/AC313414AT00ENG.png)
![](../../../img/54/AC313416BE00ENG.png)
|
(1)Disconnect the engine-A/T-ECU
connector and the combination meter connector, and measure
at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LC00ENG.png)
|
(3)Resistance between C-126
diagnosis connector terminal No.14 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364LD00ENG.png)
|
(4)Resistance between C-126
diagnosis connector terminal No.6 and body
earth OK: 1 kΩ or more
Q.
Are the check result normal?
YES <all of
the measurement results show 1 kΩ or more> :
Follow diagnostic item 16
"Diagnose CAN bus lines thoroughly." Refer to .
NO
<The resistance between terminal No.14 and body earth
is less than 1 kΩ> : Go to
Step 3.
NO <The resistance between terminal
No.6 and body earth is less than 1 kΩ>
: Go to Step 26.
|
![](../../../img/54/AC313414AB00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from
the connector. For details refer to .
|
Q.
Is the check result normal?
Go to Step
4.
Repair
the defective connector.
|
![](../../../img/54/AC313414AB00ENG.png)
|
(1)Disconnect the connector, and
measure at its male-side intermediate connector (at the
front wiring harness side). (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LE00ENG.png)
|
(3)Resistance between C-125
intermediate connector terminal No.27 and body
earth OK: 1 kΩ or more
Q.
Is the check result normal?
<1
kΩ or more> Go to Step 5.
<less
than 1 kΩ> Go to Step 18.
|
![](../../../img/54/AC313414AR00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from
the connector. For details refer to .
|
|
![](../../../img/54/AC209350AB00ENG.png)
|
When checking the joint connector,
ensure that its wiring harness side and its short pins
are not damaged.
Q.
Is the check result normal?
Go to Step
6.
Repair a
defective connector or replace the joint
connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the connector, and
measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LI00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.17 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364LF00ENG.png)
|
(4)Resistance between C-09 joint
connector (CAN2) terminal No.19 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364MF00ENG.png)
|
(5)Resistance between C-09 joint
connector (CAN2) terminal No.16 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364MG00ENG.png)
|
(6)Resistance between C-09 joint
connector (CAN2) terminal No.20 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209365LI00ENG.png)
|
(7)Resistance between C-09 joint
connector (CAN2) terminal No.21 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364LG00ENG.png)
|
(8)Resistance between C-09 joint
connector (CAN2) terminal No.18 and body
earth OK: 1 kΩ or more
Q.
Are the check result normal?
YES <all of
the measurement results show 1 kΩ or more>
: Go to Step 17.
NO <The resistance between
terminal No.17 and body earth is less than 1
kΩ> : Go to
Step 7.
NO <The resistance between terminal
No.19 and body earth is less than 1 kΩ>
: Go to Step 8.
NO <The resistance between
terminal No.16 and body earth is less than 1
kΩ> : Go to
Step 10.
NO <The resistance between terminal
No.20 and body earth is less than 1 kΩ>
: Go to Step 12.
NO <The resistance between
terminal No.21 and body earth is less than 1
kΩ> : Go to
Step 14.
NO <The resistance between terminal
No.18 and body earth is less than 1 kΩ>
: Go to Step 16.
|
![](../../../img/54/AC313416AU00ENG.png)
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the joint connector
(CAN2) and the combination meter connector, and measure
at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LI00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.17 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the combination meter
connector.
|
![](../../../img/54/AC313416AB00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
9.
Repair
the defective connector.
|
![](../../../img/54/AC313414AR00ENG.png)
![](../../../img/54/AC313416AB00ENG.png)
|
(1)Disconnect the joint connector
(CAN2) and the A/C-ECU connector, and measure
at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LF00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.19 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<less than 1.0
V> Follow diagnostic item 16 "Diagnose CAN bus
lines thoroughly." Refer to .
<1.0 V or
more> Repair the wiring harness between the joint
connector (CAN2) and the A/C-ECU
connector.
|
![](../../../img/54/AC313421AE00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
11.
Repair
the defective connector.
|
![](../../../img/54/AC313414AR00ENG.png)
![](../../../img/54/AC313421AE00ENG.png)
|
(1)Disconnect the joint connector
(CAN2) and the ETACS-ECU connector, and measure at the
wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364MF00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.16 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the ETACS-ECU
connector.
|
![](../../../img/54/AC313416BD00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
13.
Repair
the defective connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the joint connector
(CAN2), and measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364MG00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.20 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the no connection
connector.
|
![](../../../img/54/AC313414AS00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
15.
Repair
the defective connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the joint connector
(CAN2), and measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209365LI00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.21 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the no connection
connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the connector, and
measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LG00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.18 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the diagnosis
connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the connector, and
measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364MH00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.22 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the intermediate
connector.
|
![](../../../img/54/AC302572AD00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
When checking the joint connector, ensure that its
wiring harness side is not damaged.
Q.
Is the check result normal?
Go to Step
19.
Repair a
defective connector or replace the joint connector (front
wiring harness
assembly).
|
![](../../../img/54/AC302572AD00ENG.png)
|
(1)Disconnect the connector, and
measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LN00ENG.png)
|
(3)Resistance between A-07 joint
connector (CAN1) terminal No.3 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364LO00ENG.png)
|
(4)Resistance between A-07 joint
connector (CAN1) terminal No.2 and body
earth OK: 1 kΩ or more
Q.
Are the check result normal?
YES <all of
the measurement results show 1 kΩ or more>
: Go to Step 25.
NO <The resistance between
terminal No.3 and body earth is less than 1
kΩ> : Go to
Step 20.
NO <The resistance between terminal
No.2 and body earth is less than 1 kΩ>
: Go to Step 23.
|
![](../../../img/54/AC313371AD00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
21.
Repair
the defective connector.
|
![](../../../img/54/AC302572AD00ENG.png)
![](../../../img/54/AC313371AD00ENG.png)
|
(1)Disconnect the joint connector
(CAN1) and the intermediate connector, and measure at the
wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LN00ENG.png)
|
(3)Resistance between A-07 joint
connector (CAN1) terminal No.3 and body
earth OK: 1 kΩ or more
Q.
Is the check result normal?
<1
kΩ or more> Go to Step 22.
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN1) and the intermediate
connector.
|
![](../../../img/54/AC313371AD00ENG.png)
![](../../../img/54/AC313414AT00ENG.png)
|
(1)Disconnect the engine-A/T-ECU
connector and the intermediate connector, and measure at
the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LP00ENG.png)
|
(3)Resistance between A-16
intermediate connector terminal No.12 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
Ω> Repair the wiring harness between the
intermediate connector and the engine-A/T-ECU
connector.
|
![](../../../img/54/AC313371AN00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
24.
Repair
the defective connector.
|
![](../../../img/54/AC302572AD00ENG.png)
![](../../../img/54/AC313371AN00ENG.png)
|
(1)Disconnect the joint connector
(CAN1) and the ABS-ECU connector, and measure at the wiring
harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LO00ENG.png)
|
(3)Resistance between A-07 joint
connector (CAN1) terminal No.2 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN1) and the ASC-ECU
connector.
|
![](../../../img/54/AC302572AD00ENG.png)
![](../../../img/54/AC313414AB00ENG.png)
|
(1)Disconnect the joint connector
(CAN1) and the intermediate connector, and measure at the
wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LQ00ENG.png)
|
(3)Resistance between A-07 joint
connector (CAN1) terminal No.1 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN1) and the intermediate
connector.
|
![](../../../img/54/AC313414AB00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from
the connector. For details refer to .
|
Q.
Is the check result normal?
Go to Step
27.
Repair
the defective connector.
|
![](../../../img/54/AC313414AB00ENG.png)
|
(1)Disconnect the connector, and
measure at its male-side intermediate connector (at the
front wiring harness side). (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LR00ENG.png)
|
(3)Resistance between C-125
intermediate connector terminal No.26 and body
earth OK: 1 kΩ or more
Q.
Is the check result normal?
<1
kΩ or more> Go to Step 28.
<less
than 1 kΩ> Go to Step 41.
|
![](../../../img/54/AC313414AR00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from
the connector. For details refer to .
|
|
![](../../../img/54/AC209350AB00ENG.png)
|
When checking the joint connector,
ensure that its wiring harness side and its short pins
are not damaged.
Q.
Is the check result normal?
Go to Step
29.
Repair a
defective connector or replace the joint
connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the connector, and
measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LX00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.6 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364ME00ENG.png)
|
(4)Resistance between C-09 joint
connector (CAN2) terminal No.8 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364LU00ENG.png)
|
(5)Resistance between C-09 joint
connector (CAN2) terminal No.5 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364MI00ENG.png)
|
(6)Resistance between C-09 joint
connector (CAN2) terminal No.9 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364LY00ENG.png)
|
(7)Resistance between C-09 joint
connector (CAN2) terminal No.10 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364MJ00ENG.png)
|
(8)Resistance between C-09 joint
connector (CAN2) terminal No.7 and body
earth OK: 1 kΩ or more
Q.
Are the check result normal?
YES <all of
the measurement results show 1 kΩ or more>
: Go to Step 40.
NO <The resistance between
terminal No.6 and body earth is less than 1
kΩ> : Go to
Step 30.
NO <The resistance between terminal
No.8 and body earth is less than 1 kΩ>
: Go to Step 31.
NO <The resistance between
terminal No.5 and body earth is less than 1
kΩ> : Go to
Step 33.
NO <The resistance between terminal
No.9 and body earth is less than 1 kΩ>
: Go to Step 35.
NO <The resistance between
terminal No.10 and body earth is less than 1
kΩ> : Go to
Step 37.
NO <The resistance between terminal
No.7 and body earth is less than 1 kΩ>
: Go to Step 39.
|
![](../../../img/54/AC313416AU00ENG.png)
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the joint connector
(CAN2) and the combination meter connector, and measure
at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LX00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.6 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the combination meter
connector.
|
![](../../../img/54/AC313416AB00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
32.
Repair
the defective connector.
|
![](../../../img/54/AC313414AR00ENG.png)
![](../../../img/54/AC313416AB00ENG.png)
|
(1)Disconnect the joint connector
(CAN2) and the A/C-ECU connector, and measure
at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364ME00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.8 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the A/C-ECU
connector.
|
![](../../../img/54/AC313421AE00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
34.
Repair
the defective connector.
|
![](../../../img/54/AC313414AR00ENG.png)
![](../../../img/54/AC313421AE00ENG.png)
|
(1)Disconnect the joint connector
(CAN2) and the ETACS-ECU connector, and measure at the
wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LU00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.5 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the ETACS-ECU
connector.
|
![](../../../img/54/AC313416BD00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
36.
Repair
the defective connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the joint connector
(CAN2), and measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364MI00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.9 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the no connection
connector.
|
![](../../../img/54/AC313414AS00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
38.
Repair
the defective connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the joint connector
(CAN2), and measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LY00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.10 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the no connection
connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the connector, and
measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364MJ00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.7 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the diagnosis
connector.
|
![](../../../img/54/AC313414AR00ENG.png)
|
(1)Disconnect the connector, and
measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364MK00ENG.png)
|
(3)Resistance between C-09 joint
connector (CAN2) terminal No.11 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN2) and the intermediate
connector.
|
![](../../../img/54/AC302572AD00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
When checking the joint connector, ensure that its
wiring harness side is not damaged.
Q.
Is the check result normal?
Go to Step
42.
Repair a
defective connector or replace the joint connector (front
wiring harness
assembly).
|
![](../../../img/54/AC302572AD00ENG.png)
|
(1)Disconnect the connector, and
measure at the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LZ00ENG.png)
|
(3)Resistance between A-07 joint
connector (CAN1) terminal No.6 and body
earth OK: 1 kΩ or more
|
![](../../../img/54/AC209364MA00ENG.png)
|
(4)Resistance between A-07 joint
connector (CAN1) terminal No.5 and body
earth OK: 1 kΩ or more
Q.
Are the check result normal?
YES <all of
the measurement results show 1 kΩ or more>
: Go to Step 48.
NO <The resistance between
terminal No.6 and body earth is less than 1
kΩ> : Go to
Step 43.
NO <The resistance between terminal
No.5 and body earth is less than 1 kΩ>
: Go to Step 46.
|
![](../../../img/54/AC313371AD00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
44.
Repair
the defective connector.
|
![](../../../img/54/AC302572AD00ENG.png)
![](../../../img/54/AC313371AD00ENG.png)
|
(1)Disconnect the joint connector
(CAN1) and the intermediate connector, and measure at the
wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364LZ00ENG.png)
|
(3)Resistance between A-07 joint
connector (CAN1) terminal No.6 and body
earth OK: 1 kΩ or more
Q.
Is the check result normal?
<1
kΩ or more> Go to Step 45.
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN1) and the intermediate
connector.
|
![](../../../img/54/AC313371AD00ENG.png)
![](../../../img/54/AC313414AT00ENG.png)
|
(1)Disconnect the engine-A/T-ECU
connector and the intermediate connector, and measure at
the wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364MB00ENG.png)
|
(3)Resistance between A-16
intermediate connector terminal No.6 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
Ω> Repair the wiring harness between the
intermediate connector and the engine-A/T-ECU
connector.
|
![](../../../img/54/AC313371AN00ENG.png)
|
caution |
The strand end of the twist
wire should be within 10 cm from the connector.
For details
refer to .
|
Q.
Is the check result normal?
Go to Step
47.
Repair
the defective connector.
|
![](../../../img/54/AC302572AD00ENG.png)
![](../../../img/54/AC313371AN00ENG.png)
|
(1)Disconnect the joint connector
(CAN1) and the ABS-ECU connector, and measure at the wiring
harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364MA00ENG.png)
|
(3)Resistance between A-07 joint
connector (CAN1) terminal No.5 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN1) and the ASC-ECU
connector.
|
![](../../../img/54/AC302572AD00ENG.png)
![](../../../img/54/AC313414AB00ENG.png)
|
(1)Disconnect the joint connector
(CAN1) and the intermediate connector, and measure at the
wiring harness side. (2)
caution |
When measuring the resistance,
disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is
disconnected.
|
![](../../../img/54/AC209364MC00ENG.png)
|
(3)Resistance between A-07 joint
connector (CAN1) terminal No.4 and body
earth OK: 1 kΩ or more (4)
caution |
Strictly observe the specified
wiring harness repair procedure.
For details refer to .
|
Q.
Is the check result normal?
<1 kΩ or
more> Follow diagnostic item 16 "Diagnose CAN
bus lines thoroughly." Refer to .
<less than 1
kΩ> Repair the wiring harness between the
joint connector (CAN1) and the intermediate
connector.
|